Numbers of digits for the scher khan alarm 5. Programming the Scher-Khan car alarm keyfobs

To set autostart from the Scher-Khan magicar 5 key fob, press button 2 on the key fob and hold it down for more than two seconds. With this manipulation, the car will be set to armed mode with the engine running, the doors will be locked, and after that the engine will be started. If the engine is started successfully, then the key fob will display information about how much time is left for the engine to run before stopping (it is most convenient if the time interval is programmed in minutes - from 5 to 45 minutes). If the launch has taken place, then in the distance you can see light smoke from the exhaust pipe.

To start a trip, during the set autostart interval, when it has not yet expired, open the driver's door, insert the ignition key into the lock and switch it to the position that corresponds to the inscription on the ignition on. All these actions must be done in no more than 20 seconds, if you delay in time, the ignition will not turn on and the engine will be turned off. As you understand, this is provided to prevent malicious attempts to steal your car.

If the launch fails, the Sherkhan Magikar 5 system will make a second and then a third attempt to start the engine. If all three attempts to start did not take place, then the security system will stabilize in standby mode. To re-initiate the autostart function, you must first make sure that the engine is working.

Why autorun Scher-Khan magicar 5 does not work

Possible reasons autostart not triggering the following:

• discharged battery;
• the temperature outside the window in winter has reached a critically low level (preventing the easy operation of this function);
• other ICE systems could malfunction, making it difficult to start the engine;
• car electrical failure
• problems are related to the immobilizer, which prevents autorun;
• the indicator shows smoke, although the engine did not start, so the system does not attempt to start 2.

If, when the key is flogged, the ignition works, and the auto start from a distance does not work, then you need to reprogram it, you can try to do the following - make the start periods shorter and set the response temperature higher.

How the Sherkhan Magikar 5 alarm works during launch:

When it is not possible to set to autorun:

• with the ignition off;
• if not all car doors are closed;
• if the motor is already running;
• in cars with mechanical transmission - if the "redundancy" mode is not active.

If the remote start is successful, then the corresponding systems behave as follows:

When the engine is automatically stopped, the systems behave as follows:

How to set the warm-up interval for autorun Sherkhan Magikar 5

To proceed with the installation of Scher-Khan magicar 5 in time, simultaneously with two fingers, press the first and second buttons on the key fob and hold the buttons like that for some time. (The autostart interval is possible 2, 4 or 6 hours - which specific value to choose depends on the condition of the battery and engine.)

1. Briefly press the Roman buttons 2 and 4 once without holding them down - this will turn off the timer.

2. Press the Roman button 4 13 times (after each pressing, the siren will confirm), then wait until the siren confirms the received signals 13 times.

3. It remains to select the autorun interval: to set autorun after two hours, press the Roman button 4, so that after 4 hours, press the Roman 3, after 8 hours, press the Roman 2.

4. Finally, finish the auto-start setting by turning on the timer by pressing Roman buttons 2 and 4 once and immediately releasing them.

How to set autorun Sherkhan Magikar 5 by temperature in the cabin

1. First, in a way already known to us, you need to turn on the autorun mode by time - to do this, press button 4 13 times (after each press, the siren will confirm), and then wait until the siren confirms the received signals 13 times.

2. Switch to programming mode. To do this, simultaneously press two fingers on the first and second buttons on the key fob and hold the buttons like that for some time.

1. Deactivate the timer (if it is not already off) by briefly pressing buttons 2 and 4 simultaneously.
2. Press 21 times on the Roman button 4 - the siren should turn on.
3. Wait until the siren sounds 21 times, and then proceed to the temperature selection.
4. To turn on autostart at minus 25°С, press button 3, at minus 15°С, press button 2.
5. Restart the timer? by pressing buttons 2 and 4.

How to program the warm-up time

The warm-up time on the Sherkhan Magikar 5 alarm can be selected in the form of specific time periods in minutes (5, 15, 25 or 45 minutes).

1. First you need to turn on the programming function by simultaneously long pressing buttons 1 and 2.
2. Press button 4 12 times, each press will be accompanied by an audible confirmation, and the final confirmation of programming is 12 siren sounds in a row.
3. It remains to set the warm-up time. To warm up for 45 minutes, press button 4 to 25 minutes. – button 3, 15 min. – button 2 and 5 min. – button 1.

How to program autostart by on-board voltage

You can program auto start, in case the battery is discharged to 11.5 volts.

• Enter the time trigger mode by pressing button 4 13 times.
• Activate the programming function by simultaneously long pressing buttons 1 and 2.
• Press button 4 20 times without stopping, after which the siren will also sound 20 times.
• Press button 2 - in this way you will turn on the autostart operation mode by battery voltage.

The most common problems with autorun

1. The “Valet” mode is activated when the car is urgently disarmed (zzzz signs appear on the key fob). To solve the problem, you need to, with two fingers at the same time, press buttons 1 and 3 for more than 2 seconds.
2. When the ignition is off, the car does not stall. The doors are locked, and in order to deactivate autorun, you need to activate the car's doors. To get out of this situation, you need to use button 2 to perform functions from 1 to 16. To turn off the engine, you must turn the ignition key to the "Ignition Off" position.
3. If you urgently need to remotely turn off the engine when autostart is running, then press button 2 and hold it.

Video: Setting up the autostart alarm Scher Khan magicar 5 on a manual transmission

Video: The car does not start with the Scher Khan magicar 5 alarm. Finding the cause

If the video is not showing, refresh the page or

Hands-free mode on Sherkhan 5 is designed to automatically arm the car. The anti-theft system is activated when the key fob is removed from the vehicle at a certain distance.

[ Hide ]

How to enable and disable Hands Free?

The instructions for the car alarm provide for two options for the Free Hands Sherkhan 5 mode:

1. At a distance of 15 meters from the car. In this mode, the indicator on the screen is in a calm state.
2. At a distance of 35 meters from the vehicle. In this case, the "Hands free" indicator will be active on the screen.

"Hands free" indicator on the key fob The designation of the "Free hands" function in the instructions

To change, enable and disable, proceed as follows:

1. In order to change the operating mode or remove it altogether, press and hold the I button on the key fob for two seconds.
2. To enable/disable the free hands function of Sherkhan 5, you need to hold down the I button on the key fob.

Setting the hands-free mode

How to set the time on the Magikar 5 model?

The Magicar 5 key fob can start the engine using an internal timer. The LCD screen will display the “Timer” icon. In order for the function to work correctly when using it for the first time or after having to remove the batteries, the clock must be set.

According to the manual, the setup is as follows:

1. Combined press buttons II and III. The car will beep.
2. Press I for less than a second. The time on the screen should flash.
3. Using the keys I and II set the exact value of hours and minutes.
4. To fix the set value, leave the programming mode by simultaneously pressing buttons I and II. A signal should sound.

Incorrect time setting leads to desynchronization of the indications on the key fob and on the real clock. Because of this, it is not possible to correctly set the autostart by timer on the alarm. Warming up the engine and interior will be carried out at the wrong time.

You need to set the time in accordance with the real clock, for more accurate synchronization.

Setting the time for Keychain Magicar 5 is shown in the video of the author Marat.

Enabling and disabling the "Turbo" mode on Magikar 5

When operating a car that has a turbocharged engine, special maintenance methods are used:

1. To prevent the destruction of the injection mechanism, the car must not be turned off directly after stopping.
2. To eliminate the waiting time for the turbine to cool down, a turbo timer is used.
3. Signalka Magikar 5 makes it possible to cool the turbine, while not being in the car. The engine runs for about 2 minutes after the trip is completed.

To enable or disable this mode, press the III and IV keys for a short time. The state of the function will determine which signals or icons will be displayed on the key fob.

To autostart Sherkhan 5 from the key fob, press and hold button II for at least 2 seconds, as shown in the figure.

ATTENTION! Found a completely simple way to reduce fuel consumption! Don't believe? An auto mechanic with 15 years of experience also did not believe until he tried it. And now he saves 35,000 rubles a year on gasoline!

In this case, the car will forcibly switch to armed mode with the engine running. The doors will automatically enter the close mode, after which the system will be set to the engine start mode. If the process of starting the engine is successful, then the key fob will display information about the time remaining before the engine stops working in minutes-seconds, and smoke from the exhaust pipe. This time can be programmed in the modes of 15, 5, 25 minutes or 45. To make a trip without stopping the engine within the programmed auto start duration, it is necessary to open the driver's door, then insert the key into the ignition lock, turn it to the "Ignition On" position. The period of time between opening the door and turning on the ignition mode is limited to 20 seconds. This event is provided in order to increase the security of the car against theft during the warm-up period. If within 20 sec. the ignition will not turn on, the engine will stop.

If the engine start was unsuccessful, the security system will try to start again. After 3rd failed attempt the car alarm will go into standby mode. To resume the autorun function, it is necessary to diagnose the engine and the main systems of the car. Possible reasons why the engine start does not work:

• weak battery charge;
• extremely low engine temperature in the cold season;
• immobilizer problems limiting remote engine start;
• malfunction of the electrical equipment of the car;
• there is no control over starting the engine (the engine did not start, but there is smoke on the indicator, so a second attempt to start is not made);
• failure of other internal combustion engine systems associated with difficulty starting.

If the engine is started with the key, but the remote start does not work, it is necessary to reprogram the autostart system, reducing the starting frequency, increasing temperature regime triggering. Perhaps the problem will be fixed.

When starting the engine, the security system will signal the following signals.

The car is not set to autorun, if during its production:

• the ignition is in the "On" position;
• one of the doors is open;
• the engine is already running;
• the "reserve" mode is not activated in cars with manual transmission.

In the event of a successful engine start, the devices will signal:

In the case when the engine stops automatically, the devices generate signals:

Programming autorun time intervals

The car alarm provides programming of time intervals (autostart time) after two, 4 and 8 hours. The choice of a specific option is made depending on the operating conditions of the car, the condition of the engine and the battery. To start the programming operation, it is necessary to simultaneously long press the buttons I and II. Next, you need to perform the following operations in the following sequence:

1. Turn off the “timer” option (if it is activated) by briefly pressing buttons II and IV at the same time. The "timer" should be deactivated on the display.
2. Press the IV button thirteen times. Each entry is confirmed by one siren signal.
3. Wait for the siren to give a 13-fold sound confirmation of the entered information.
4. Use the key fob buttons to confirm the selected autorun mode. Button II corresponds to the autostart mode after 8 hours, III - after 4 hours, IV - after two hours.
5. Set to autostart by turning on the "timer" mode by briefly pressing buttons II and IV at a time.

Reprogramming the autostart mode according to the interior temperature

For correct activation of autostart according to the characteristics of the passenger compartment temperature, it is necessary to activate the start modes by time (1-13) before enabling the programming option. Next, you need to switch to the programming mode by long pressing the corresponding buttons on the key fob I + II. Then the following operations are performed:

1. Turn off the "timer" mode (if it is activated), as described in the previous paragraph.
2. 21 times methodically press the IV-th button, after which the siren will signal.
3. Wait for the siren alarm 21 times in a row.
4. Set the desired autostart temperature mode: button IV - plus 60 degrees Celsius, III - minus 25, II - minus 15.
5. Activate the timer mode.

Warm-up programming

The warm-up time can be set to fixed intervals of 5, 15, 25 minutes or 45 minutes. To do this, activate function 1-12 in mode II. Programming is entered by long pressing I + II, after which the following operations are performed:

1. Button IV is pressed twelve times (accompanied by a sound signal).
2. 12-fold siren signal - confirmation.
3. The engine operation time is selected by activating buttons I (5 minutes), II - 15, III - 25 or IV - 45 minutes.

Programming autostart by the voltage of the on-board network

Autostart can be programmed when the battery is discharged to an amplitude of 11.5 volts. First you need to activate the start by time (1-13), then enter the programming by long pressing I + II. Here are the buttons to press:

1. 20 consecutive IV button presses.
2. Waiting for the siren to sound 20 times.
3. Activate the battery voltage response mode with button II.

Autorun problems

Some vehicles have the following autostart problems:

1. When the ignition is turned off, the car does not stall. To disable autorun, you need to open and close the doors. To correct the problem, function 1-16 (Button II option) is required. In this case, in order to turn off the engine, it is necessary to switch the key to the "Ignition Off" position.
2. Activation of the "Valet" mode after emergency disarming (zzz symbols on the key fob). To fix the problem, simultaneously long (more than 2 seconds) press the I + III buttons.
3. If it is necessary to urgently turn off the car from the key fob during the autostart period, it is necessary to long press the II button.

Programming the CTCTS functions using a key fob consists of four steps.

1. Enter programming mode and select the programming menu. To enter Menu No. 1, press the I + II buttons simultaneously for 2 seconds. To enter Menu No. 2, press the I + IV buttons simultaneously for 2 seconds. The siren will give one short signal, alarm the car will flash once, confirming the successful completion of STEP 1.

2. Press the IV button to select the Menu function you want to change. The number of presses must correspond to the number of the selected function. For example, to select function 4, you need to briefly press the keyfob button IV four times. Each button press will be confirmed by a short siren sound (if enabled) and a flash of the car alarm.

3. Wait a few seconds. The system will confirm the number of the selected function to be changed with short siren beeps and car alarm flashes. The number of signals will correspond to the number of the selected function.

Note:

If, when choosing a function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all the steps starting from STEP 1.

4. Press the I button to select the factory setting for the function. To confirm this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select optional function values. To confirm this, the siren will give two, three or four short beeps, the car alarm will flash two, three or four times.

Note:

If you hear one long signal from the car alarm siren, this means that the system has exited the function programming mode. To continue programming, repeat all steps from STEP 1.

ATTENTION!

If you want to change more than one function from the Menu you have selected, then the selection of each function to change must begin with STEP I.

Menu of programmable functions

Menu #1 [Button (I + II)-]

			[Button (II)]	[Button (W)]
	Delay before the starter rotates after the ignition is turned on. Should be increased for a diesel vehicle.
	Open door warning
	The duration of the control pulse of the central lock. Should be increased for pneumatic central locking system
	Panic mode or JackStop ™ (robbery protection)	"Panic" (Starter lockout)	JackStop™ (Ignition Interlock)
	Control central lock on and off the ignition	Turned off	Included
	Launch reservation method. (Only for manual transmission)	Automatically, every time the ignition is turned off	Automatically, whenever the ignition is turned off, but provided that the doors are closed	Only manual mode, before switching off the ignition for reservation, it is necessary to press button II for 2 seconds.
	Starter rotation time	Standard	Standard + Minimum	Standard + maximum

Note on function 1-4: This function allows you to select Panic mode or JackStop™ mode (robbery protection):

.
	IV button for 2 sec.	IV button for 2 sec.
	Siren sounds 1.5 min.	Siren sounds 1.5 min.
Engine lock type	Starter lock	Ignition lock (lock is disabled during automatic start)
Starter lock	Turns on immediately	Not used
Ignition lock	Not used	Turns on immediately if the ignition is off. Turns on after 30 sec. after 2 sec. pressing the IV button if the ignition is on

Resetting all programmable functions of Menu No. 1 to factory defaults

1. Enter programming mode. Press buttons I + II simultaneously for 2 sec. The car alarm siren will sound one short beep and the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the car alarm key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time after this, three siren sounds will sound, the alarm will flash three times, confirming the factory settings of all programmable menu #1 functions.

Menu #2 [Button (I+IV)-]

		[Button (I)] Factory setting	[Button (II)]	[Button (III)]	[Button (IV)]
	Timer start operation mode	24 hours (start time is user selectable)	2 hours (periodically to warm up the engine)
	Engine warm-up time
	Pulse time for add. channel 1

Resetting all programmable functions of Menu No. 2 to factory defaults

To reset the programmable features to factory defaults, two steps are required.

1. Enter programming mode. Press buttons I + IV simultaneously for 2 sec. The car alarm siren will beep once, the alarm will flash once, confirming the success of STEP 1

2. Briefly press button III on the key fob three times. Each press will be confirmed by a short siren tone and an alarm flash. After some time, three siren sounds will sound, the car alarm will flash three times, confirming the factory settings of all programmable car alarm functions menu No. 2

KEYFOB-COMMUNICATOR CAR ALARM SCHER - KHAN 5

Preparing the key fob-communicator for work

Before using the key fob, you must bring it into working condition, because. during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before operation. Before using the key fob, remove it. To do this, release the battery cover lock, press the cover and slide it in the direction opposite to the antenna. Remove the battery. Remove the insulating pad between the battery and the collector plate. Install the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is set with a negative terminal towards the antenna. Close the battery cover. After that, the keychain is ready to work.

Symbols on the display of the key fob-communicator of the car security system

	Timer start indicator
	TURBO mode indicator
	Passive arming indicator
	"Hands free" mode activation indicator
	Siren indicator
	Shock sensor off indicator
	Power indicator vibration call
	Indicator of turning on the automatic control of the central lock by ignition
	Door open indicator
	Trunk/hood open indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator

Scher Khan security systems have a long range of two-way communication. Autorun Sherkhan 5 can be performed according to several settings, depending on the desire of the owner.

[ Hide ]

Main characteristics

Deactivation of the signaling from the key fob

The system can operate in a passive mode, when the protection is activated half a minute after closing all doors and covers on the body. If the doors do not open when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by briefly pressing the second and third buttons of the main key fob.

Passive operation mode is active (the Passive icon is lit on the display)

If the doors and the trunk lid were opened and closed, the system will turn on protection half a minute after the lock of the last element is clicked into place.

Keychain - communicator

The main key fob supplied in the kit has the following functional features:

• thanks to the four-button scheme, it is possible to control all system functions;
• the signal from the key fob is encoded according to a special Magic Code scheme, which prevents interception and recording;
• the built-in display with illumination provides visual display of all operations;
• when working with the system, the key fob confirms commands with a sound or vibration signal;
• additional information from sensors can be displayed on the screen;
• the key fob is the main tool for programming automatic start;
• using the key fob, the system parameters are configured.

After unpacking and installing the system on the car, it is necessary to bring the main key fob into working condition. To do this, you will need to remove the dielectric gasket installed between the contact pads of the battery and the key fob power circuit.

Action algorithm:

1. Open the battery cover. To do this, open the latch and slide the cover to the bottom of the key fob.
2. Remove the battery from the compartment.
3. Remove the gasket located along the entire length of the element.
4. Return the battery to the local location, observing the installation polarity indicated on the sticker. If there is no marking, remember that the negative pole of the battery is always directed towards the antenna of the Sherkhan Magikar key fob.
5. Close the lid and lock the latch.

Pictograms on the keychain Sherkhan Magikar 5

The following symbols and icons may appear on the screen:

• timer start (A);
• turbo timer mode (B);
• passive activation of the system (C);
• automatic activation mode without pressing the buttons (D);
• included siren (E);
• shock detection sensor (F) is off;
• vibrating alert is active in the key fob (G);
• control of door locks after starting the ignition (H);
• open trunk lid (J);
• the engine is switched on in the autostart mode (K);
• system state (L);
• open doors (M);
• field for displaying hours, temperature and data during autorun (N);
• operating mode Valet (O);
• working alarm or dimensions not switched off (P);
• shock sensor triggering (Q);
• key fob battery indicator (R);
• signal level (S).

Marat Askarov demonstrates setting the clock in the Magicar 5 key fob.

Autostart security system

Under the autostart of the system, they mean turning on and off the protection without pressing the buttons on the key fob. The mode is called “hands free” and is activated by pressing button one on the main key fob for two seconds. The system automatically turns on or off at a distance of up to 35 meters from the vehicle. When operating the alarm in conditions of strong interference, this distance can be reduced to 15 meters.

The black oval highlights the hands-free mode icon

The hands-free mode can only be controlled using the main key fob with a display.

Auto engine start

When using automatic start, you need to remember and follow a few rules:

1. Using autorun is allowed only when the machine is placed in a ventilated area and subject to visual contact.
2. Do not start automatically when people are standing in front or behind the vehicle.
3. The parked car must be fixed with a working parking brake.
4. Before turning on the autostart function on machines with a manual method of gear shifting, it is necessary to set the “software neutral”.
5. Monitor coolant or oil levels.
6. Set in advance on the microclimate control unit the direction of airflow and the desired air temperature in the cabin.
7. Do not pass the key fob to play with children.

Before turning on the engine start system on vehicles with a manual gearbox, the neutral position of the gearbox lever must be programmed. There are three options for this, the description of the steps for each of them is given below. The mode can be programmed through the system settings menu.

The first option provides:

1. Stop in a parking space, apply the parking brake, move the gearshift lever to neutral and remove the key from the lock cylinder.
2. With the engine still running, open the door, leave the vehicle and slam it behind you. The motor must stop.

If you need to pick up things from the trunk, then you should use the second option:

1. After setting the lever to the neutral position and turning off the ignition, the driver exits the car and does not close the door behind him.
2. Open the trunk and take out everything you need.
3. Close the door and then slam the luggage compartment lid. The engine will stop and be ready for automatic start.

The third option looks like this:

1. Set the neutral position and apply the parking brake.
2. Close doors.
3. Press button two on the key fob for two seconds.
4. Turn off the ignition and get out of the car.
5. Close the door, after which the motor will stop.

When installing autorun on the machine, the neutral setting procedure is not required, just put the box selector in the parking mode.

To provide remote engine start, it is necessary to install a device to bypass the immobilizer.

The engine can be started by pressing the second key fob button. After starting the engine, the display will show the remaining operating time. This parameter is programmable and can be 45/25/15 or 5 minutes. If necessary, the car door can be opened by pressing the first button and within 20 seconds, insert the key into the lock and turn to the active ignition position.

Display in engine mode

Autostart by timer

To connect and disconnect the function, a short press on the buttons three and four is used, after which the icon with the inscription Timer will turn on on the screen.

There are two options for working, which are configured programmatically:

• daily run, repeating every 24 hours;
• auto-restart every 2/4/8 hours.

To enable daily start, a so-called redundant mode must be carried out.

For this you need:

1. Turn off the timer mode by briefly pressing buttons two and four.
2. To enter the setting, press buttons one and two for a few seconds.
3. Turn on the mode by pressing 13 times on the button four. Each press will be accompanied by a signal.
4. Select the repeat time by pressing the buttons (the second button gives a repeat of 8 hours, the third - 4 hours and the fourth - two hours).
5. Enable timer.

Enable timer start

Auto start by battery temperature and voltage

The engine is switched on according to the temperature inside the cabin minus 15 or 25 degrees in winter time and plus 60 in the summer.

1. Turn off the timer start mode.
2. Press button four 21 times.
3. Use the buttons to select the switching threshold (the fourth - plus 60, the third - minus 25 and the second - minus 15).
4. Enable timer.

When setting the voltage in the on-board network, the system will operate at a value of 11.5 V.

1. Press 20 times on the fourth button.
2. Turn on voltage start with button two.

In all warm-up modes, you can vary the operating time of the power unit.

For this, the steps are:

1. Press button number four twelve times.
2. Select the operating time using the buttons from the first to the fourth, choosing each time from the range of 5-15-25-45 minutes.

Scher-Khan Magicar 5 alarm auto start malfunctions

The main causes of malfunctions that are possible when auto-starting the Sher-Khan Magikar 5 alarm:

1. The engine does not start even though automatic start backup is running normally. The cause may be oxidized fuse legs in the power supply circuit of the main unit. Another reason may be the failure of the standard immobilizer crawler or the sticking of the contacts in the control relay.
2. The motor starts and then stalls after a few seconds of operation. At the same time, in normal mode, the engine starts without problems from the ignition switch. One of the probable causes could be damage inside the five-pin relay installed in the main unit.
3. A common reason why the start does not work is incorrect parameter settings. To eliminate this, you must return the system to factory settings and re-program.
4. Sometimes the reason that the automatic start stopped working may be the inclusion of the Valet mode. This mode is characterized by a permanently lit control diode. After the setting mode is turned off, the start returns to normal.