Alarm Sherkhan 5 with auto start refers to budget systems and is intended for use in cars, the voltage of which is 12 volts. The car alarm has two-way communication, which operates within a radius of 1500 m.
[Hide]
Scher-Khan Magicar 5 Alarm Feature
This model of the signaling can be installed on a car with a manual transmission or on an automatic machine. The security device is powered by a rechargeable battery.
Main functions
Options provided by the multifunctional communicator keyfob:
- confirmation of the executed commands by means of sound or vibration;
- protection of the communication channel from interception of code data, the system is called "Magic code";
- playback of sound signals when the alarm mode is activated;
- backlight of the liquid crystal screen of the device;
- designation of the power supply charge inside the communicator;
- determination of the voltage level in the electrical network of the vehicle;
- designation of the temperature value in the car interior;
- determination of the current time on the screen;
- output of the operating time of the power unit, started automatically;
- the ability to remotely start the engine of the machine;
- setting the start time of the power unit with an accuracy of minutes;
- reminder mode via sound or visual messages;
- the ability to program all the options of the anti-theft installation.
Description of the options performed by the microprocessor module:
- remote start of the power unit on vehicles with any type of transmission;
- operation of the system on gasoline and diesel internal combustion engines, including those equipped with turbines;
- the ability to start the power plant by a command sent from the communicator;
- option to configure remote start by timer, every 2 hours, or by alarm every day;
- the ability to monitor the state of the running motor in accordance with the signals sent from the generator set or noise in the power grid;
- availability of a personal password to access the vehicle interior in case of key loss;
- use of power outputs to control the central lock, luggage compartment door, as well as light signaling;
- setting of the blocking relay type - normally closed or normally open;
- mode of automatic activation of the protective option;
- sound warning before activating the automatic mode of protection;
- re-activation of the protection function if the vehicle door has not been opened;
- the ability to activate the protection mode without being accompanied by siren signals;
- the presence of two universal programmable channels used to control additional equipment;
- microprocessor module allows additional connection of positive and negative door controllers;
- the presence of a separate input for installing a negative sensor in the luggage compartment;
- the ability to close and open door locks when starting and stopping the power unit in automatic mode;
- activation of the protection mode with or without confirmation signals;
- an option to warn the car owner about an open door with a light alarm, this mode must be pre-programmed;
- Panic function, allowing to activate the operation of the siren and light signaling on command;
- the Hands-free option, which makes it possible to automatically enable or disable the protective function if the car owner approaches the car or moves away from it;
- function of warning the driver about the included side lights.
The Autoazart channel briefly spoke about the options and capabilities of the Sherkhan Magikar 5 security complex.
Technical specifications
The main properties of the anti-theft installation:
- the range of the communicator is up to 1500 meters in ideal terrain;
- the keychain is powered by AAA batteries;
- optimal operation of the anti-theft system is possible in the on-board network at 9-18 volts;
- the current strength when the system is running is 20-35 mA;
- the temperature range at which the security complex operates is from -40 to +85 degrees Celsius;
- the total mass of the microprocessor module is 270 g.
Car owner alert signals are divided into several groups:
- sound for the siren - when the alarm mode is activated, their duration is 30 seconds, the signals are played continuously;
- optical for car headlights - signals with a power of 1 Hz and a duration of 30 seconds function on two channels and are reproduced intermittently;
- using a radio channel - information is transmitted to the communicator and reproduced intermittently.
The exact range of the key fob depends on many factors:
- power supply charge;
- the presence of interference on the ground;
- obstacles in the form of large structures, structures, transformer substations;
- weather conditions.
Information is transmitted to the communicator over a secure channel using encryption.
All electrical circuits of the security complex are protected by means of safety, resistor devices and transistors. To prevent voltage surges and noise, the system is equipped with varistors. If, during the connection, errors related to polarity are made, this will not affect the operation of the signaling, since the power supplies are equipped with diode elements.
Contact controllers react to opening door locks or turning the key in the ignition switch. If such a sensor is triggered, the signal will play an alarm without the possibility of shutting down without a remote control. The security complex with auto start Sherkhan 5 also reacts to physical influences on the body and, when they are fixed, issues alarm signals.
The values of the currents for the protection of electrical circuits are given in the table.
| Description of the power line | Amount of current |
| Blocking the operation of the ignition systems and the starter mechanism | 0,2 |
| Turning lights on the left side of the body | 10 |
| Turn signals on the right side of the car | 10 |
| Ignition system | 30 |
| Additional ACC circuit | 30 |
| Starter power line | 30 |
| Additional electrical circuit of the ignition system | 0,2 |
| Drive line of locks of the left front and rear doors | 15 |
| Electric circuit of the drive mechanism of the locks of the right front and rear doors | 15 |
| Additional channel for the lock installed on the tailgate | 10 |
| Additional first channel | 0,2 |
| Additional second channel | 0,2 |
| Communication channel with factory alarm | 0,2 |
User guide
A key fob or an ignition key can be used to control the anti-theft complex. At correct setting this procedure is carried out using the panic button. Using the remote control, you can program functions and set a password for emergency shutdown or activation of the system.
Setting up a PIN
To set up a personal password, you need to enter the programming mode:
- The vehicle is disarmed.
- The door lock of the machine is opened.
- The ignition is activated by installing and turning the key in the lock. The motor should not start.
- The third and fourth keys are clamped on the communicator keyfob. The alarm will blink once with light devices, the siren will go off. If the signal is triple, this indicates an unsuccessful attempt to enter the password setting mode.
- The first digit of the code is entered, for this the consumer is given four seconds after the siren signal. To set the values, use the communicator keys, the selected digit corresponds to the button. If the symbol is accepted successfully, the alarm will play the corresponding number of flashes and siren signals.
- Subsequent digits are indicated identically, each car owner is given four seconds to enter. When the last character is entered, the system will automatically exit the setup mode. The car owner will be informed about this by a double siren signal and two flashes of light devices.
- Then you can turn off the ignition and lock all the doors of the car.
To open a vehicle using the code, follow these steps:
- The car alarm is deactivated.
- The driver's door opens.
- The key is inserted into the lock, the ignition is activated.
- The car owner taps the call controller ten times. The time interval between impacts should be 1.5 seconds. With each subsequent impact, the diode element will blink red.
- Each character of the password is configured by the method of strikes, their number must correspond to a digit. Confirmation of input is carried out every 1.5 seconds. When you indicate each digit, the diode will blink blue.
- Similarly, each character of the password is indicated. In confirmation, the alarm will blink with lights and sound a siren.
If the car owner enters the PIN-code settings mode, the diode lamp will flash blue.
The channel "Videomax12345" spoke about the main settings and functions of the anti-theft system.
How to enable security mode?
You need to start the healed mode after turning off the ignition and closing all the door locks of the car. To complete the task, the first key on the remote control is clicked. This will block the door locks and starter mechanism.
When this function is activated, the following occurs:
- the siren sounds once;
- the lights of the car are blinking;
- the diode indicator flashes on the unit at 1 second intervals;
- the vehicle headlights blink five times on the communicator display and the locked padlock indicator appears;
- the remote control emits a melodic signal.
The indicator in the form of a locked padlock is displayed on the communicator until the protection mode is disabled. When the security is turned on, the alarm constantly monitors and analyzes the readings issued by the controllers. 30 seconds after the protection is turned on, the sensitivity sensor is activated. If the power unit remains running, the arming procedure is the same. All doors are locked and the first key on the pager is clicked.
But the sensitivity controller will remain off until the ignition is working. Security mode indication will be similar. Signals will be checked 30 seconds after turning off the power unit.
User Sergey Gorin showed several ways to control the security mode of the Magikar 5 signaling.
System check
The fourth key is used to diagnose the state of the anti-theft device. After pressing it, the car alarm analysis data will be displayed on the communicator screen. Information about the check will be confirmed by siren signals, as well as light signaling.
System shutdown
To disarm the system, use the second key of the communicator. In confirmation, the siren will play one signal, the car lights will go off. The headlights of the car will blink on the pager screen, an indicator with an open lock will appear.
Keychain - communicator
Before using the remote control, you need to install a power supply.
To do this, a protective cover is removed on the back of the communicator, into which the battery is inserted observing the polarity. Then the lid is closed.
Indicator designation
Key designations on the remote control display
Description of symbols on the communicator screen:
- A - timer operation of the power unit;
- В - turbo timer option;
- С - passive security activation mode;
- D - the option of automatic activation of the guard without clicking on the keys;
- E - activated siren;
- F - sensitivity controller is disabled;
- G - the communicator has the vibration alert function enabled;
- H - door locks control after activation of the ignition system;
- J - opened door luggage compartment;
- K - the power unit is started in automatic start mode;
- L - the state of the anti-theft installation;
- M - open door locks;
- N - information field for displaying clock data, and temperature regime with automatic start;
- О - the service mode of functioning of the Jack is enabled;
- R - the light alarm is on on the car or the parking lights are not turned on;
- Q - activation of the sensitivity controller;
- R - communicator power supply icon;
- S - signal level.
Keychain main functions
To adjust the main parameters and set functions, use the button combinations shown in the table.
| Key number | Pressing duration | System function |
| 1 | 0.5 sec | Used to activate options:
|
| 1 | 2 seconds | Activation of the Hands-free option in the first operating mode, the indicator does not blink |
| 1 | 2 sec | Activation of the Hands-free function in the second operating mode with a blinking indicator |
| 1 | 2 sec | Disable the Hands-free option, the indicator disappears |
| 3+4 | 2 sec | Simultaneous click will result in recording and playback of the fragment on the audio module |
| 2 | 0.5 sec | Additional first channel control function |
| 3 | 0.5 sec | Option to control an additional second channel |
| 4 | 0.5 sec | Diagnostics of the state of the anti-theft installation |
| 2 | 2 sec | The function allows you to start and stop the power unit on command from the communicator |
| 3 | 2 sec | Command to open the tailgate |
| 4 | 2 sec | Panic mode, the first key is used to disable |
| 1+2 | 0.5 sec | Command to activate mute siren |
| 1+3 | 0.5 sec | Combination for disabling and activating the Jack service mode |
| 1+4 | 0.5 sec | Command for automatic control of the central lock by ignition |
| 2+3 | 0.5 sec | Automatic activation and deactivation of protection mode |
| 2+4 | 0.5 sec | Timer start option |
| 3+4 | 0.5 sec | Command to activate and deactivate Turbo mode |
| 1+3 | 2 sec | Command to disable and enable the sensitivity controller |
| 1+2 | 2 sec | Button for entering programming mode 1 |
| 1+4 | 2 sec | Command to activate programming mode 2 |
How to bring the key fob into working order?
The procedure for binding a new communicator is as follows:
- A key is inserted into the lock, after which the ignition is switched on and off three times. Light signaling should work once, which indicates entering the configuration mode.
- Over the next four seconds, you need to click on the first button on the communicator.
- Then the pager code is entered into the memory of the microprocessor module.
The car owner can record no more than three communicators. Therefore, when setting up the fourth device, information about the first is deleted from the microprocessor memory. To exit the settings mode, do not touch the key fob for four seconds.
Channel "MasikBonLive" spoke about the independent binding of the new communicator to the microprocessor signaling module.
Configuring autorun
There are four options for setting the autostart option on the Sherhan system:
- by command:
- by time;
- by air temperature;
- to reduce the voltage in the on-board network of the car.
Configuring launch on command
The option is activated as follows:
- The transmission lever is set to the neutral position, and the handbrake is activated. If the car is equipped with an automatic transmission, then the gearshift knob is moved to the parking position.
- All door locks of the vehicle are locked.
- Button 2 on the communicator is held down for two seconds.
- The ignition is turned off, the driver leaves the car.
- The driver's door closes, this should cause the engine to stop.
- To subsequently start the operation of the power unit, the second key on the communicator is clicked.
Time Trigger Setting
The user can configure the option to be triggered daily, with a repeat every 24 hours. You can also configure it to start every 2, 4 or 8 hours. To activate the function, you need to complete the reservation procedure.
To complete the task you need:
- Disable timer function. To do this, click the keys 2 and 4.
- To activate the programming mode, buttons 1 and 2 are pressed, they must be pressed for 2 seconds.
- To enter the setup menu, the fourth key is clicked 13 times. With each subsequent click, a signal will sound.
- The repeat time is selected by pressing the keys. When you click on the second button, the time will be 8 hours, on the third - 4 hours, on the fourth - 2 hours.
- The timer is being activated.
User Marat Askarov spoke in detail about setting the time on the Sherkhan Magikar 5 alarm communicator.
Temperature trigger setting
When this function is activated, the readings of the temperature controller installed in the passenger compartment are used. In the cold season, the values can be -15 or -25 degrees, in the warm - up to +60 degrees.
The setting is done like this:
- The option to start the engine by timer is disabled.
- The fourth key is clicked 21 times.
- Use the keys to select the threshold for disabling the option. Button 2 to turn on the internal combustion engine at -15 degrees Celsius, button 5 - at -25 degrees, and 4 - at +60.
- After selecting a value, the option is activated.
Configuring autostart according to the voltage of the on-board network
If you configure this function, then the autostart threshold will be 11.5 volts of voltage in the mains:
- Key numbered 4 is clicked 20 times.
- The voltage trigger is activated by the second button.
- To change the operating time, the fourth key is clicked 12 times.
- Time selection is made using buttons 1-4.
How do I disable autoplay?
Resetting autorun settings is performed in the same way as their purpose. To disable the option, select the corresponding function on the key fob and set its inactive status.
The Galileosky channel spoke about the implementation and disabling of the autostart option.
Possible malfunctions of the Scher-Khan Magicar 5 alarm
If the autostart stops working and the engine does not start, the reason depends on the nature of the breakdown:
- The powertrain will not start, but the car owner has completed the backup procedure. With such a problem, the first reason why the options do not work may be the oxidation of contacts on safety device... The element is installed in the power supply circuit of the main module. Also, the reason may lie in the incorrect operation of the bypass device of the standard blocker. Sticking of contact elements in the control relay is possible.
- The motor starts but stops after a few seconds of operation. If you start the engine with a key, it will turn on. The problem may lie in the failure of the five-contact relay, which is located in the microprocessor module.
- Incorrect setting of the autorun function. To solve the problem, you need to reset all the settings of the anti-theft complex to the factory settings. Then the option values are readjusted.
- The problem may lie in the activated Jack service mode. If this function is enabled, the diode element will light up without interruption. After turning off the service mode, the function will resume.
How to install an alarm?
It is necessary to mount and connect the systems as follows:
- The battery is disconnected to remove voltage from the on-board network.
- The microprocessor device is being installed. To do this, you need to remove the lining in the cabin and put the unit in a hidden place. During installation, the device is securely fixed to prevent the negative impact of vibrations on the module. It is recommended to place the unit under the dashboard or in the free space behind it.
- The siren is being installed under the hood of the car. The place must be chosen so that there are no sources of moisture nearby or high temperatures... The siren is mounted with the horn downwards to prevent moisture accumulation inside. After installation, you need to make sure that the device and its wires will not be accessible from under the bottom of the car.
- An antenna module with a diode indicator is installed. Installation of these elements is carried out on the inner surface of the windshield, it must first be cleaned and degreased. Fixation is carried out with glue or double-sided tape.
- The temperature controller is being installed, as well as the shock sensor. These elements are installed in the vehicle interior. The wires for their connection are laid under the plastic sheathing.
- Limit switches are installed on the doors, luggage compartment and bonnet. The wires from them must be laid so that they do not come into contact with moving parts of the body. The cables are laid under the cladding.
- A service button is installed in the car interior. Its installation must be carried out in a hidden place, but the consumer must have access to the button from the driver's seat. The button can be disguised by wrapping it with black electrical tape.
- At the final stage, all components are connected to the microprocessor module. The engine blocking relay is connected to the ignition switch.
Download Scher-Khan Magicar 5 installation and operating instructions in PDF format
A detailed guide on how to properly use and install the alarm can be downloaded from the link.
How much does the Scher-Khan Magicar 5 alarm cost?
The approximate cost of the anti-theft system is shown in the table.
Video "A detailed review of the anti-theft system Magikar 5"
Channel "Ramin Drive" presented a video describing the main features and functions of this anti-theft installation.
Sherkhan 5 is the ability to remotely control security using a key fob. The car alarm consists of two components - directly a switch with an LCD display and a processor unit built into the car.
[Hide]
Description and characteristics
The processor unit connects directly to the car battery and operates on 12 volts. Its main function is driving a car, receiving and transmitting information from sensors.
The keyfob switch is used to control the system by the user. In particular, setting a PIN code, programming functions, as well as enabling and disabling vehicle protection.
The equipment is supplied with an additional key fob and detailed instructions... At the same time, there is a manual for both operation and installation of the system. However, it is not recommended self-assembly systems. It is better to ask the car service masters to deliver it.
Main functions
The key fob switch is designed to directly influence the system by the user. It is equipped with four control buttons and a display showing all necessary current information.
It can be used to turn the system on and off, as well as program the main unit. In this case, the power source is only one AAA battery.
The choice of one or another command is displayed on the screen, and is also accompanied by sound and vibration. The backlight of the display occurs automatically when pressing buttons, as well as when an alarm signal is received.
The functionality of the electronic key fob also includes:
- MAGIC CODE - protection against interception of encoded data;
- display of the current battery level;
- displaying the voltage level of the car battery;
- the ability to remotely start the engine, including delayed.
You can also check the current temperature in the cabin and see the current time.
The key fob has a special signal reception range and is capable of functioning at a distance of up to one and a half meters from the car. The processing unit is directly responsible for the protection of the vehicle and the reaction to pressing the buttons of the key fob.
Its main functions are:
- automatic engine start on command;
- indication of the delay time for the activation of accessories;
- disabling car protection by PIN-code in the absence of a key fob;
- getting access to the salon using PIN2;
- control of the central lock of the car and the trunk lock;
- control alarm;
- the ability to protect the car when the engine is running.
- The settings allow you to start the engine in the following ways:
- at intervals of two, four or eight hours;
- every day at a certain time;
- by analyzing vehicle indicators - temperature or voltage.
Another available function is programming the maximum and minimum starter rotation time, as well as setting it to increase with an increase in the number of starting attempts.
PIN codes are set by the user and used for emergency access to the vehicle.
Technical specifications
This system can be built into any car, regardless of the type of engine and gearbox. It is possible to start engines equipped with a turbine.
There are three types of alerts:
- audible siren - lasts for thirty seconds, sounds continuously;
- optical - power one hertz, also lasts thirty seconds, operates on two channels, is issued intermittently;
- via a radio channel - the range is up to one and a half meters, lasts one hundred milliseconds at a frequency of 0.35 hertz, sounds intermittently.
The exact range of your switch will vary depending on a number of factors, including obstacles, interference, specific weather conditions, and battery level.
The system is controlled in one of the following ways:
- remotely using a key fob;
- from the ignition key;
- due to the triggering of the driver's call sensor;
- as a reaction to certain sensor signals.
Electrical circuits are protected by fuses, resistors and transistors. They are additionally equipped with varistors to protect against voltage surges and interference. The functioning of the system, even when the polarity of the power supplies is reversed, is ensured by diodes.
There are contact sensors that react to opening doors or turning the ignition lock. In this case, the system issues an alarm signal without the possibility of turning it off.
The system also reacts to shocks by issuing a signal lasting up to 30 seconds in one cycle. All radio transmissions of the keyfob take place over a secure channel using special coding.
The processor unit is characterized by the following parameters:
- work at voltage from 9 to 18 volts;
- current strength from 20 to 35 milliamperes is allowed;
- works at temperatures ranging from -40 to +85 degrees Celsius;
- the total weight of the device is 270 grams;
- dimensions 150x120x32 mm.
User guide
The system can be configured through the block or from the remote control. The first is controlled by blows, and the second - by buttons. The functionality of the key fob is very wide.
With its help you can:
- set automatic arming;
- stop alarm mode;
- block the ignition or starter;
- activate the "Free hands" option;
- remotely turn on and off the engine;
- activate the "Panic" mode;
- open the trunk;
- connection of the "Turbo" mode;
- program PIN1-code.
The system block allows you to apply and change PIN2, as well as activate a call to the car owner.
PIN-code programming
Setting your own PIN1 code takes a few minutes and is not a complicated procedure.
To switch to the programming mode, you need to perform a number of actions:
- Disable the arming mode first.
- Then open the car door.
- Turn on the ignition, but do not turn on the engine.
- Then make a long (about 2 seconds) joint pressing of buttons 3 and 4 on the remote control.
The system will respond with a single beep and flash. However, if you receive a 3x beep in response, it means that you have not entered the programming mode. Check if you did everything right. It is important that the security mode is turned off, and the ignition, on the contrary, is turned on.
The first digit of the PIN-code is indicated for four seconds after the signal. This is done by pressing the key fob button. Its number is equal to the selected digit. The selection is confirmed by the corresponding number of signals and flashes.
The remaining four digits of the code are entered in the same way. They also need to be specified within four seconds. Entering the latter automatically ends the programming mode. This will be indicated by a double siren sound and two alarm flashes.
After completing the input, you can turn off the ignition and close the car doors.
The PIN2 code is set in the same way:
- To do this, you need to remove the security mode, open the door and turn on the ignition.
- Then you need to hit the call sensor ten times with an interval between strikes of less than one and a half seconds. A red LED will respond to each hit.
The activation of the programming mode will be accompanied by a fast blinking of the blue LED. Each digit is programmed by strokes. Their number corresponds to the number. One and a half seconds after the input, the input is confirmed. The unit emits an appropriate number of blue flashes, after which it switches back to blinking mode.
The remaining digits of the code are entered in the same way. Confirmation of data entry and exit from the programming mode will be accompanied by a single siren sound and a single alarm flash.
Enabling security mode
In order to turn on the security mode, you must turn off the ignition of the car and close all the doors. After that, a single short press of button 1 on the key fob is made. Thus, the mode is activated, the starter is blocked and all doors are locked.
The activation of the mode is accompanied by the following indication:
- one-shot siren sound;
- single flashing of the alarm;
- blinking of the indicator with an interval of one second;
- five times flashing of car headlights and the icon of a closed lock on the key fob;
- single beep from the switch.
After that, the closed lock icon lights up and is displayed until the vehicle is unlocked. From this moment on, the system continuously analyzes and monitors the sensor readings. Thirty seconds later, the shock sensor is activated.
In the event that the engine remains on, the process of setting the security mode is slightly different. As in the previous case, it is necessary to close all doors and press button 1 on the switch once.
The mode activation indication is similar to the previous case. In this case, the shock sensor will be disabled until the ignition of the car is turned off. Thirty seconds after stopping the engines, the analysis of such signals is activated.
To disable the security mode, use button 2 on the key fob.
Keychain - communicator
Before you start using the key fob, you need to configure it. The first step is to install the battery.
The symbols on the display show the following information:
- transmitter signal strength;
- battery charge level;
- indicator of hours, as well as the level of voltage and temperature in the car;
- the state of the lock (open / closed) and the security mode;
- disabling the shock sensor;
- activation of the vibration signal;
- data on the running timer;
- TURBO mode (enabled / disabled);
- state of the VALET mode;
- display of an open trunk and / or car doors;
- siren signaling;
- inclusion of dimensions;
- visual display of the alarm.
There are also some other symbols that represent certain processes.
System check
By pressing the fourth button, you can check the status of the system. The information will be shown on the display.
Cabin temperature 
Battery voltage
The information is also confirmed by a siren and alarm.
Signal table when checking the state of the vehicle system
Autostart security system
Automatic activation of the car security system is possible. It can be programmed using a key fob.
In this case, the system is transferred to the armed mode 30 seconds after all doors are locked. In this case, a corresponding indication and a siren are issued. For another thirty seconds, you can still open the trunk or car doors. If this is done, the automatic switch-on countdown is delayed by another half a minute.
If this function is enabled, the PASSIVE indicator will be displayed on the keyfob display.
Autostart engine
The system assumes automatic engine start. This is necessary primarily to maintain certain parameters of the car, as well as warm up when it is parked.
Automatic start can be regulated both by sensors and by a timer set by the user.
Autostart by temperature and battery voltage
Automatic start of the engine on the machine can occur by timer or based on the readings of temperature and voltage sensors.
Thus, the number of timer starts is controlled depending on the temperature in the cabin or the voltage level of the car battery. This is configurable with a key fob.
The temperature threshold can take one of the following values: -15, -25, +60 degrees Celsius. The limitation according to the voltage level can take only one value - 11.5 Volts. Thus, it is possible to adjust the timer activation depending on the current parameters of the sensors. This allows you to regulate the temperature of the passenger compartment, as well as maintain the operating voltage in the battery.
Timer autostart
It is necessary to set the remote autostart of the system by timer in this way: simultaneously press buttons 2 and 4. It is also with their help that the start time is set.
After the timer is turned on, the TIMER indicator on the display lights up, and the engine operation is regulated according to the time specified by the user.
Four different engine starting modes are possible according to the preset timer:
- daily at a specified time;
- periodically, every eight hours;
- every four hours;
- every two hours.
Periodic switching is used to control the temperature in the passenger compartment (heating or cooling the space).
It is possible to install only one mode, it is not supposed to combine them. Setting a different behavior model automatically disables the previous one.
Turning on and off the engine start according to the timer is accompanied by sound signals and light indication. The display flashes five times.
The exact time of the automatic start must be specified only during daily switching on. In all other modes, the report starts from the moment the function is enabled.
Why the autostart of the Scher-Khan Magicar 5 alarm may not work
If the Sherkhan Magikar 5 autorun system is unable to remotely start the engine, the key fob will emit three short signals. Accordingly, there will be three flashes of alarm, and after three seconds a series of flashes will occur. This series displays what error occurred.
Therefore, depending on the number of flashes, it is possible to determine why the engine does not start:
- If there is one blink, it means that the engine is already on.
- If two - the ignition is on.
- If three - opening one of the doors prevents the start.
- If four - a similar situation, but with the trunk or the hood.
- In the event that the system responded to you by flashing five times, the start reservation for the vehicle in mechanical transmission has not been made.
If the remote engine start fails, the system will try to start it again. In the event that this cannot be done three times in a row, the alarm will go into standby mode. If this happens, the car will no longer start, you need to contact the service center to determine the cause of the problem.
Video "Autostart stopped working"
What to do if the car does not start from autostart is described in the video from SerЁga.
The system can memorize the codes of three key fobs. Follow two steps to program new keyfobs.
1. Turn the ignition key three times from OFF to ON.
The alarm will flash once to confirm entering the programming mode.
2. Not later than 4 sec. after the flashing of the alarm, press the button I of the key fob, the code of which must be entered into the memory of the processor unit.
If after step 1 no action is taken, after 4 sec. the alarm will flash 2 times, the system will switch from the keyfob programming mode to the VALET mode.
Note: the system has three memory cells for storing keyfob codes. If you try to write the fourth keyfob, the code of the first recorded keyfob will be deleted.
Sher-Khan 7.8
KEY FOB PROGRAMMING
The system can memorize the codes of three key fobs.
To write keyfob codes:
1) In the "disarmed" mode with the ignition on, press the button on the call sensor body for 2 seconds. Alarm will flash once
2) Within 5 sec. briefly press the call sensor button. The alarm will flash twice if the personal code PIN 1 is not used (programmable function 1-6 in the factory
value, see page 69) or once if using PIN 1 (programmable function 1-6 in optional value)
3) If PIN 1 is used, it is necessary to enter its value (“Entering the personal code PIN 1 in the keyfob programming mode”, items 5 to 8 on page 60). The alarm will flash twice
4) After 5 sec. the LED will light up blue, confirming the readiness to enter the keyfob codes
5) Within 5 sec. shortly press button I of the first remote control. In confirmation of the code recording, the alarm will flash 1 time. Then you can enter the code of the second and third keyfobs, after successfully entering the code of each new keyfob, the alarm will flash 1 time, after entering the code of the third keyfob, the alarm will flash twice and the system will exit the keyfob programming mode.
When writing the code of at least one new key fob, the codes of all key fobs previously recorded in the system memory will be deleted
To exit programming mode, do not take any action for 4 seconds. after writing the code of the last keyfob.
If after step 4 no action is taken, then after 5 sec. You will hear one siren signal *, the alarm will flash once, the system will switch from keyfob programming mode to VALET mode.
Sher-Khan Jungle, Vegas
PROGRAMMING NEW KEY FOBS
The system can memorize the codes of four key fobs.
To start programming new key fobs, you need to:
Disarm the system
Turn on the car ignition
In the case when the PIN code is not used (the factory value of the programmable function is 20), the following sequence of actions must be performed:
1) Within 5 seconds, shortly press the VALET button three times. The system will confirm the action taken with one flash of the alarm
2) Within the next 5 seconds, briefly press the button of the first remote control. The system will confirm the successful entry of the keyfob code with one flash of the alarm. The new keyfob code will be added to the processor unit memory. This will delete the keyfob code that was programmed first.
3) In the case when it is necessary to program the codes of several key fobs, it is necessary to sequentially press the button on each of them with a time interval between presses of at least 1 second and no more than 5 seconds. The system will confirm each press with one flash of the alarm.
If no action is taken within 5 seconds, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm
4) If four key fobs are programmed, then after pressing the button on the last of them, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm. In the event that less than four keyfobs are programmed and it is necessary to delete the codes of the previous keyfobs from the memory, press the button on any of the keyfobs several times until the system exits the programming mode (two flashes of the alarm)
In the case when a PIN code is used (value 2 of programmable function 20), for programming new
keyfobs, you must perform the following sequence of actions:
1) Entering the first digit of the PIN-code (factory value - "1"). To do this, shortly press the VALET button in a row the required number of times, corresponding to the first digit of the PIN-code. The time interval between clicks should be no more than 3 seconds. After that, do not perform any action for 3 seconds. After this time has elapsed, the system will confirm the entry of the first digit with one flash of the alarm
2) Entering the second digit of the PIN-code (factory value - "1"). To do this, shortly press the VALET button in a row the required number of times, corresponding to the second digit of the PIN-code. To enter the PIN code correctly, you must start entering the second digit no later than 3 seconds after the alarm flashes, confirming the entry of the first digit. The time interval between clicks should also be no more than
3 seconds. After entering the second digit, do not perform any action for 3 seconds. After this time has elapsed, the system will confirm the entry of the correct PIN-code values with one flash of the alarm. If two flashes of the alarm signal follow, it means that the PIN-code was entered incorrectly, while the system returns to the initial mode and it is impossible to update the keyfob codes.
After three unsuccessful attempts entering a PIN-code, this operation is blocked for 30 minutes
3) Within 5 seconds after confirming the correct PIN-code entry, shortly press the button of the first remote control. The system will confirm the successful entry of the keyfob code with one flash of the alarm. The new keyfob code will be added to the processor unit memory. This will delete the keyfob code that was programmed first.
4) When it is necessary to program the codes of several keyfobs, it is necessary to sequentially press the button on each of them with an interval of time between presses of at least 1 second and no more than 5 seconds. The system will confirm each press with one flash of the alarm. If no action is taken within 5 seconds, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm
5) If four remote controls are being programmed, after pressing the button on the last of them, the system will automatically end the mode of programming new remote controls, which will be confirmed by two flashes of the alarm. In the event that less than four keyfobs are programmed and it is necessary to delete the codes of the previous keyfobs from the memory, press the button on any of the keyfobs several times until the system exits the programming mode (two flashes of the alarm)
Sher-Khan 6
PROGRAMMING TECHNIQUE FOR NEW KEYROBS
ATTENTION!
The system has a secure algorithm for writing new key fobs,which excludes unauthorized recording of key fobs into memorysystems. To ensure the secrecy of the recording, do not forget to enter the codeemergency shutdown PIN 1.
The system can memorize the codes of three key fobs. To start programming, the system must be disarmed using the key fob or emergency using the PIN1 ignition lock or using the PIN2 call sensor. Also, on the keyfob being recorded, the Hands Free function must be turned off.
Follow four steps to program new keyfobs:
1. Turn the key in the ignition switch from OFF to ON three times. The alarm will flash once to confirm that the first step has been completed. Switch off the ignition.
2. Not later than 4 sec. after the flash of the alarm, turn on the ignition the number of times corresponding to the first digit of the personal code (factory value is "1"). Switch off the ignition. The alarm will flash once to confirm that the second digit is ready.
3. Not later than 4 sec. after the flash of the alarm, turn on the ignition the number of times corresponding to the second digit of the personal code (factory value is "1"). Switch off the ignition.
The alarm will flash once to confirm that the third digit is ready.
4. Not later than 4 sec. after the flashing of the alarm, press the button I of the key fob, the code of which must be entered into the memory of the processor unit. With an interval of no more than 4 seconds, you can press buttons 1 of the three key fobs, then the system will remember their codes. If it is necessary to write down the code of only one remote control, then shortly press the button I of this remote control three times.
To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last keyfob.
Two flashes of the alarm will follow, confirming the exit from the keyfob codes programming mode.
Note:
The system has three memory cells for storing keyfob codes. When trying to write the fourth keyfob, the code of the first recorded keyfob
Scher Khan security systems have a long range two-way communication. Autostart Sherkhan 5 can be performed in several settings, depending on the wishes of the owner.
[Hide]
Main characteristics
Deactivating the signaling from the keychain
The system can operate in a passive mode, when the protection is activated half a minute after all doors and covers on the body are closed. If the doors are not opened when the system is turned off, it will automatically arm. To use the passive mode, it should be activated by short pressing on the second and third buttons of the main remote control.
Passive operating mode is active (the Passive icon is lit on the display)
If the doors and the trunk lid were opened and closed, the system will turn on the protection half a minute after the lock of the last element is clicked.
Keychain - communicator
The supplied main key fob has the following functional features:
- thanks to the four-button scheme, it is possible to control all the functions of the system;
- the signal from the keyfob is encoded according to a special Magic Code scheme, which prevents interception and recording;
- built-in backlit display provides visual display of all operations;
- when working with the system, the key fob confirms the commands with a sound or vibration signal;
- additional information from sensors can be displayed on the screen;
- the key fob is the main tool for programming the automatic start;
- the keyfob is used to configure the system parameters.
After unpacking and installing the system on the car, you must bring the main key fob into working condition. To do this, you need to remove the dielectric gasket installed between the contact pads of the battery and the power supply circuit of the key fob.
Algorithm of actions:
- Open the battery compartment cover. To do this, open the latch and slide the cover towards the bottom of the key fob.
- Remove the battery from the compartment.
- Remove the gasket along the entire length of the element.
- Return the battery to the locally, observing the polarity of the installation, which is shown on the sticker. If there is no marking, remember that the negative pole of the battery is always directed towards the antenna of the Sherkhan Magikar key fob.
- Close the cover and snap the catch.
Pictograms on keychain Sherkhan Magikar 5
The following symbols and icons can be displayed on the screen:
- timer start (A);
- turbo timer mode (B);
- passive activation of the system (C);
- automatic switching on without pressing the buttons (D);
- siren on (E);
- the shock detection sensor is turned off (F);
- vibration alert is active in the key fob (G);
- door locks control after ignition start (H);
- open trunk lid (J);
- the engine is turned on in autostart mode (K);
- system state (L);
- open doors (M);
- field for displaying hours, temperature and data at autostart (N);
- Valet (O) operating mode;
- working alarm or unplugged dimensions (P);
- shock sensor triggering (Q);
- key fob battery indicator (R);
- signal level (S).
Marat Askarov demonstrates the installation of the clock in the Magikar 5 key fob.
Autostart security system
By autostarting the system, we mean turning on and off the security without pressing the buttons on the key fob. The mode is called "hands-free" and is activated by pressing for two seconds on button one on the main key fob. The system automatically turns on or off at a distance of up to 35 meters from the vehicle. When operating the alarm in an environment of strong interference, this distance can be reduced to 15 meters.
Black oval highlighted the hands-free mode icon
Hands-free control is possible only with the main key fob with a display.
Autostart engine
When using automatic start, you must remember and follow several rules:
- It is allowed to use autostart only when the machine is placed on a ventilated area and subject to visual contact.
- Do not start automatically when people are standing in front of or behind the vehicle.
- A parked vehicle must be secured with a working parking brake.
- Before turning on the autostart function on machines with a manual method of gear shifting, it is necessary to set "program neutral".
- Observe the coolant or oil levels.
- Set in advance on the microclimate control unit the blowing directions and the desired air temperature in the passenger compartment.
- Do not pass the remote control key fob to children.
Before turning on the engine starting system on vehicles with a manual gearbox, it is necessary to program the neutral position of the gearbox lever. There are three options for this, a description of the steps for performing each of them is given below. The mode can be programmed through the system settings menu.
The first option provides for:
- Stop in a parking space, set the parking brake, move the gearbox lever to neutral and remove the key from the lock cylinder.
- With the engine still running, open the door, leave the vehicle and slam it behind you. The motor should stop.
If you need to pick up things from the trunk, then you should use the second option:
- After setting the lever to neutral and turning off the ignition, the driver gets out of the car and does not close the door behind him.
- Open the trunk and take out everything you need.
- Close the door and then slam the luggage compartment lid. The engine will stop and will be ready to start automatically.
The third option is as follows:
- Move to neutral and apply the parking brake.
- Close the doors.
- Press button two on the key fob for two seconds.
- Switch off the ignition and get out of the car.
- Close the door, after which the motor will stop.
When installing autorun on the machine, the neutral setting procedure is not required, it is enough just to put the gearbox selector into parking mode.
To ensure remote engine start, it is necessary to install a device to bypass the immobilizer.
The engine can be started by pressing the second button on the key fob. After starting the engine, the display will show the remaining running time. This parameter is programmable and can be 45/25/15 or 5 minutes. If necessary, the car door can be opened by pressing the first button and, within 20 seconds, insert the key into the lock and turn it to the active ignition position.
Display in engine running mode
Timer autostart
To activate and deactivate the function, briefly press buttons three and four, after which the icon with the inscription Timer will turn on on the screen.
There are two options for working, which are configured programmatically:
- daily launch, repeated every 24 hours;
- autorepeat every 2/4/8 hours.
To enable the daily start, it is necessary to carry out the so-called mode backup.
This requires:
- Turn off timer mode by briefly pressing buttons two and four.
- To enter the setting, press buttons one and two for a few seconds.
- Turn on the mode by pressing 13 times on the button four. Each press will be accompanied by a signal.
- Select the repeat time by pressing the buttons (the second button gives a repeat for 8 hours, the third for 4 hours and the fourth for two hours).
- Turn on the timer.
Enabling timer start
Autostart by temperature and battery voltage
The engine is turned on according to the temperature inside the cabin minus 15 or 25 degrees in winter time and plus 60 in the summer.
- Disable timer start mode.
- Press the button four 21 times.
- Use the buttons to select the activation threshold (the fourth - plus 60, the third - minus 25 and the second - minus 15).
- Turn on the timer.
When adjusting the voltage in the on-board network, the system will work at a value of 11.5 V.
- Press the fourth button 20 times.
- Switch on voltage start with button two.
In all heating modes, the operating time of the power unit can be varied.
To do this, the steps are taken:
- Press button number four twelve times.
- Select the operating time using buttons from the first to the fourth, choosing each time from the range of 5-15-25-45 minutes.
Scher-Khan Magicar 5 alarm autostart malfunctions
The main causes of malfunctions that are possible when the Sher-Khan Magikar 5 alarm is triggered:
- The engine will not start, although the autostart backup is normal. This could be due to oxidized fuse legs in the main power circuit. Another reason may be the failure of the regular immobilizer crawler or sticking of contacts in the control relay.
- The motor starts and then stalls after a few seconds of running. In this case, in normal mode, the engine starts from the ignition switch without problems. One of the probable causes could be damage to the inside of the 5-pole relay installed in the main unit.
- A common reason why the start does not work is incorrect parameter settings. To eliminate this it is necessary to return the system to the factory defaults and re-program.
- Sometimes the reason that the automatic start stopped working may be the inclusion of Valet mode. This mode is characterized by a constantly lit control diode. After exiting the setup mode, the start returns to normal.
