DIY electronic crafts. Useful and simple do-it-yourself electronic devices and homemade products

Many people consider themselves far from physics people. But even with minimal knowledge (even acquired at school is enough), you can do something interesting and, most importantly, special. We are talking about do-it-yourself electronic homemade products. Their assembly schemes, as a rule, are not complicated. We will consider a few simple options for beginner electronics engineers in this article.

Cat's house

Electronic homemade products are a flight of fancy, combined with knowledge of electronics. So, for example, you can make an excellent house for a cat from an old computer monitor. To do this, you just need to disassemble it. When the bottom and walls of the monitor are separated from the boards, kinescope and all other parts, they just need to be twisted back. To make the animal more comfortable, you need to make a litter inside.

Music Box

Electronic homemade products very often serve as an object that gives joy to their owners. A striking example of this is the music box. And it doesn't just play music. It has full storage space.

For work you will need:

the box itself;
music module with a transistor;
speaker (suitable from a phone or player);
switch (possible from a wall telephone);
compartment for AAA batteries (for example, from children's toys or a flashlight).

The first step is to solder the 8050 transistor to the music module (the circuit is shown in the figure above). Next, the conductors are soldered to connect the power supply and the speaker. When applying power, it is important to observe the polarity. The speaker and board are attached with glue. The resulting design should fit in the lid of the box.

After that, the switch is installed. A loop is made from the lace and thrown over the stem. It is necessary for management. The second end of the lace is glued to the inside of the box. Its length is chosen in such a way that the music module works exactly at the moment the lid is fully opened.

The electronic module is hidden by a cut out piece of cardboard or cloth.

Electronic fishing rod

Electronic homemade schemes offer fishermen to make an electronic fishing rod. It operates on a "finger" battery. You can cast it to a depth of 5 meters. The operating time is up to 12 hours.

Electronic homemade products of this kind work on a multivibrator circuit. A piece of the board 2x6 cm is enough, on which all the elements of the circuit will be attached. The relay is selected with a resistance of up to 2.4 ohms.

home tattoo machine

Schemes of electronic homemade products in this case provide for the presence of an electric motor with a power of 12-18 watts. As a rule, all such motors have a gear on the shaft. It is necessary to glue a medium-sized button with 4 holes to it (they should remain free).

Next, choose the right pen. It will be the body of the entire product and guide the needle. A mechanical pencil works well. To connect it to the motor, a bracket is made in the shape of the letter "G". It can be made from the handle of a spoon (fork).

The needle is cut off from the guitar string. Its length should be slightly longer than that of the pencil tube. It should be from the center of the motor to the tip of the tube. The needle must be boiled for 10 minutes.

We connect the handle and the bracket with electrical tape. The long side of the brace runs along the handle. Bend the staple at the same level as the top end of the pencil. There shouldn't be any wobbles. A motor with a button is attached to the smaller side of the bracket. We pass the pen through the pencil to the motor and insert it into the hole of the button. Homemade electronic homemade products at the last stage are connected to a power source.

Stationary lamp

To illuminate the workspace at the table, homemade electronic products offer many options. One of them involves the use of a fluorescent lamp and a metal profile, which is used to fasten drywall sheets.

The profile has the shape of the letter "P" in the context. Thanks to this, it will serve not only as a holder, but also to direct (reflect) light from top to bottom.

The profile must be bent. To do this, two sides are cut. After the fold, the edges are connected with self-tapping screws to give rigidity. The lamp has a switch. For him, we make a hole in the profile. Next, the lamp is attached to the base. Strengthen the strength of the profile will help its rectangular version. For fastening to the table, we fasten a metal corner to one edge of the profile.

We do for our loved ones

When you love, you always want to please your “soul mate”. And this desire intensifies on the eve of Valentine's Day. The problem of finding a gift will help solve electronic homemade products. With your own hands, you can prepare a wonderful and amazing gift. For example - LED Valentine.

It is assembled from ready-made elements included in a special set. It can be ordered from the online store. The kit includes the following parts: transistors (3 pcs.), resistors (6 pcs.), LEDs (18 pcs.), electrolytic capacitor (3 pcs.), printed circuit board.

It is easy to assemble the product. To do this, you only need a soldering iron with a small power, which other do-it-yourself electronic homemade products are also going to. Assembly diagrams are included in the kit. They are guided during work. In this case, several points must be observed:

When installing capacitors, the polarity of the electrodes must be taken into account. The required electrode is marked on the body of the part.

Resistors during installation must correspond to the specified ratings. They are marked on the body with a color code.

Next, the LEDs are installed.

For mounting transistors there is a key in the form of a form on the case.

When working, it is important to solder parts quickly, avoiding overheating. The board will be powered by a 3 V battery. There are two wires from the board to the battery compartment, which, by the way, is suitable for any electronic toy. The battery compartment is attached to the bottom of the board with glue. This will allow you to install the board in a vertical position.

Tattooing in our time is one of the personal and creative forms of self-expression. Samuel Riley can be considered the author of the modern tattoo machine - it was he who created its prototype and brought the art of tattooing to a new level. We invite you to read the article and...

This video shows how you can make a salt lamp with your own hands, which can glow in different colors (RGB). Not much is needed to make it: Salt crystals; LED strip (RGB) with controller; A small box made of wood and plywood; Although the video is in English, but I hope that everything will be clear.

Home craftsmen quite often face the problem of high-quality cutting and cutting of various foam materials, for example, during the repair of home furniture or the manufacture of various models. Meanwhile, a do-it-yourself foam cutter will greatly facilitate this process and improve the quality of the cut. And the most...

A few months ago, I wanted to build an electric bike. To remake, I took a regular bike, purchased all the necessary parts and accessories, and got to work. Having changed the frame of the bike and almost completely remade it, I was more than satisfied with the result. A great electric bike came out at 48 volts, 15 horsepower ....

By occupation, I often have to solder a large number of small amateur radio boards and microcircuits, I tried several options for branded soldering irons, but they were all rather rough for small soldering. The most successful option was a homemade soldering iron made from a resistor. It is reliable, easy to manufacture and easy to use. With his...

Basically, most of the defects in modern electronic equipment are associated with faulty electrolytic capacitors. At the same time, the search for faulty capacitors using a capacitance meter is rather difficult, due to the fact that the capacitance of a defective capacitor may differ slightly from the nominal value, and the ESR value may be large. In most cases it is...

Today, electromagnets are used in a huge number of devices and devices. Electric shavers, a tape recorder, a doorbell - and this is a small part of those devices where it is installed. The device of an electromagnet is quite simple, and in this article I will try to explain its principle of operation and show you how to make a homemade electromagnet. An electromagnet is a device...

Surely many of us would like to have a stroboscope at home to decorate a small party and give it a little drive. As a rule, they are made on flash lamps, but unfortunately they are quite expensive and have a small resource. I decided to replace the lamps with LEDs, and I can say with confidence that such a do-it-yourself strobe light for a disco can ...

By making this antenna, you can significantly improve the reception quality and WiFi speed. It only takes a few details to do this. Its design is quite simple and in order to make it, you will not need to disassemble your computer or WiFi adapter. Another plus is the fact that this antenna ...

Surely some of you at home or in the garage have an old unnecessary CRT monitor that no one has been using for a long time, but it's a pity to throw it away. Moreover, it is heavy, it must be carried to the alphater, etc. That is why I suggest you make a house for a cat with your own hands from an old monitor. Looks...

Many electrical appliances can be repaired or made new with your own hands. For this house, there is always something that can be converted to perform new functions: an old electronic clock, a children's car, a disused computer, and much more. Useful crafts can always be repaired or redone. For work it is better to have a workshop with tools.

Equipped home craftsman's workshop

Power Supply

Homemade electronic devices need to be powered by different voltages. In particular, an adjustable power supply is needed for soldering. Such an opportunity can be provided by the LM-317 microcircuit, which is a voltage stabilizer.

Diagram of an adjustable power supply

Devices based on this circuit allow you to change the output voltage in the range of 1.2-30 V, using a variable resistor P1. The allowable current is 1.5 A, the power of the device depends on the choice of transformer.

Adjustment of the voltmeter is performed by a trimming resistor P2. To do this, set the current to 1 mA at an output voltage of the circuit of 30 V.

The more power is allocated on the microcircuit, the greater the difference between the input and output signals. To reduce heat, it requires a heatsink with a cooler.

A homemade board with an LM-317 chip is placed in a case - a computer power supply. A voltmeter and clamps to the output wires are installed on the front panel made of textolite.

Simple autoprobe

A probe for cars and other purposes should always be at hand at home, in the garage or on the road. The figure below shows a homemade circuit that allows you to check electrical circuits with a resistance of up to 10 kOhm and the presence of a voltage of 6-15 V.

The two indication circuits are connected in series to the battery and in parallel to each other. The first one consists of a resistor R1 and an LED HL1, which lights up when checking the voltage. At the same time, the battery is being charged.

Scheme and design: a) a homemade circuit that allows you to check electrical circuits with a resistance of up to 10 kOhm and the presence of a voltage of 6-15 V; b) self-made design of an autoprobe

When the circuit is being tested, current flows from the battery through circuit HL2, R2. At the same time, the HL2 LED lights up. Its brightness will be greater, the lower the resistance of the circuit.

Like all homemade products, the probe can be constructed in many ways, for example, by placing it in a transparent plastic case, which is easy to glue with your own hands.

Such devices are indispensable when repairing an electrical network or a household appliance at home. Crafts can be more complex and have additional features.

Electric appliances for heat treatment of meat products without the use of fuel are made for a small number of servings and can be used at home or in the country. To cook a shish kebab, with the help of an electric barbecue, there is no need to spend expensive hours of rest, standing on the street at the barbecue.

In specialized stores, you can choose any device, but the price decides a lot. If you have the skills to handle electricity, it will be much cheaper to make an electric barbecue with your own hands.

Designs are made in horizontal or vertical design. The power of the device usually does not exceed 1.5 kW. The meat is heated using a spiral with a tungsten or nichrome filament. All metal parts are made of stainless steel.

Typical devices are vertical heaters in the center and skewers with the product around. They are attached to the top. It is advisable to make skewers in the form of spirals, from which the meat does not slip down during cooking.

Type of vertical electric grill

For high-quality cooking of a shish kebab with your own hands, skewers should be placed as close as possible to the heater, but so that the product does not touch the spiral. When placed at a distance, the meat will not fry, but will dry.

Pieces of the product, no larger than 40 mm in size, are mounted on a skewer, which is placed vertically around the heater. Then the electricity is turned on and the coil is heated.

The basis of the heater is a heat-resistant ceramic tube, on which a spiral is wound. Mounting at the bottom is done using a special cartridge.

In the round base, special cups are attached to collect fat and a frame that serves to hold the skewers vertically.

Cups are made from stainless steel. From below, they have cruciform protrusions, which are inserted into the slots of the base. Inside they have mounted devices for attaching skewers. Fixing the cup on both sides allows them to hold the skewers vertically.

The connection must be strong and at the same time easy to disassemble for cleaning. You can make a common removable tray for all skewers.

The cross section of the supply wire is selected according to the power of the heater (2.5 or 4 mm 2). At home or in the country, there should be a 16 A socket for it.

timer for watering plants

Devices with are used for drip irrigation of a site from a container at a certain time. They can be connected to valves with any capacity.

Often branded devices do not provide the required reliability. Then the old wall clock comes to the rescue, which is in good condition, but is no longer used at home. Small magnets are attached to the ends of the minute and hour hands, and 3 reed switches on the dial.

Timer scheme for watering plants, in which a wall clock is applied

As soon as the hour hand reaches the number 7, and the minute hand reaches 12, which corresponds to the time of 7 hours, the reed switches SA1 and SA3 are triggered and the signal opens the solenoid valve. After 2 hours, the hands will move to 9 and 12, and the current through the contacts of the reed switches SA1 and SA2 will be supplied to close the valve.

The diagram shows a "rain sensor", which in wet weather closes the transistor VT1 and the valve remains permanently closed. Manual control of the solenoid valve is also provided through the buttons S1 and S2.

The clock can be set to any time the valve is turned on.

Car with remote control

Homemade radio-controlled models capture not only children, but also adults. They can be used to play at home or arrange real competitions in the yard. To assemble with your own hands, you will need a chassis with wheels, an electric motor and a body.

There is a large assortment on sale, but first of all, you need to decide which machine is best to make. The control panel can be wired or radio controlled.

When choosing parts, you should pay attention to their quality. There should be no notches, inclusions and other mechanical defects on the plastic. The wheels are sold with the chassis and should turn easily. Grip with the surface is better provided by rubber. Plastic wheels in this regard are much worse.

It is better for a beginner to take an electric motor, which is cheaper and easier to maintain than an internal combustion engine. You can choose any case or make according to your sketch.

The motor, battery and radio unit with antenna are mounted on the chassis of a mini-car. If a kit with accessories is purchased, assembly instructions are included with it.

After installing the parts, the operation of the motor is regulated. The body on the chassis is installed after everything works.

You can assemble mini-copies at home as follows:

the car is assembled carefully and by common efforts;
materials of parts of the model may differ from the original;
small and insignificant details can be omitted.

The model can be made without looping on a certain brand of car. Much depends on finances and the availability of free time. Assembling a mini-car at home with a child is of great educational value.

Work on assembling the car model is carried out according to plan. Some parts need to be bought, but old toys can be used.

The motor must match the weight of the device in terms of power. Fresh batteries or accumulators are used for power.

If you use a special autoconstructor, crafts can be very diverse. Assembly sequence:

the frame is assembled first;
the motor is mounted and adjusted;
a power supply is installed;
is fixed;
wheels are installed and adjusted.

Types of radio-controlled car models

Many homemade tricks are revealed in this video.

Electronic homemade products can make life more comfortable and save a lot of money. In addition, you can find a use for old electrical appliances so that they do not gather dust in the pantry without a purpose. Useful do-it-yourself crafts often turn out to be better than factory-made products.

Do-it-yourself motion sensor connection diagram

It happens that you need to install lighting in the country, or in the house, which will be triggered when moving or a person or someone else.

The motion sensor, which was ordered by me from Aliexpress, works well with this function. The link to which will be below. By connecting light through the motion sensor, when a person passes through his field of vision, the light turns on, burns for 1 minute. and turns off again.

In this article I tell you how to connect such a sensor if it does not have 3 contacts, but 4 like this one.

Do-it-yourself power supply from an energy-saving light bulb

When to get 12 volts for LED strip, or for some other purpose, there is an option to make such a power supply with your own hands.

DIY fan speed controller

This regulator allows smooth adjustment variable resistor fan speed.

The floor fan speed controller circuit came out the simplest. To fit into the case from an old Nokia phone charger. There also climbed the terminals from a conventional electrical outlet.

The installation is quite tight, but this was due to the size of the case.

DIY lighting for plants

There is a problem with the lack of lighting. plants, flowers or seedlings, and there is a need for artificial light for them, and this is the light we can provide DIY LEDs.

DIY brightness control

It all started with the fact that after I installed halogen lamps at home for lighting. When turned on, they often burned out. Sometimes even 1 bulb a day. Therefore, I decided to make a smooth turn-on of lighting based on a dimmer with my own hands, and I am attaching a dimmer circuit.

Do-it-yourself refrigerator thermostat

It all started with the fact that after returning from work and opening the refrigerator found it warm. Turning the thermostat knob did not help - the cold did not appear. Therefore, I decided not to buy a new unit, which is also rare, but to make an electronic thermostat on the ATtiny85 myself. With the original thermostat, the difference is that the temperature sensor is on the shelf, and not hidden in the wall. In addition, 2 LEDs appeared - they signal that the unit is on or the temperature is above the upper threshold.

DIY soil moisture sensor

This device can be used for automatic watering in greenhouses, flower greenhouses, flower beds and indoor plants. Below is a diagram by which you can make the simplest sensor (detector) of soil moisture (or dryness) with your own hands. When the soil dries out, voltage is applied, with a current of up to 90mA, which is quite enough, turn on the relay.

It is also suitable for automatically turning on drip irrigation to avoid excess moisture.

Fluorescent lamp power circuit

Power supply circuit for a fluorescent lamp.

Often, when energy-saving lamps fail, the power circuit burns out in it, and not the lamp itself. As known, LDS with burned-out filaments, it is necessary to feed the mains with rectified current using a starterless starting device. In this case, the filaments of the lamp are shunted with a jumper and to which a high voltage is applied to turn on the lamp. There is an instantaneous cold ignition of the lamp, a sharp increase in voltage on it, when starting without preheating the electrodes. In this article, we will look at do-it-yourself LDS lamp start.

USB keyboard for tablet

Somehow, suddenly, he took something and decided to buy a new keyboard for his PC. The desire for novelty is unstoppable. Changed the background color from white to black, and the color of the letters from red - black to white. A week later, the desire for novelty naturally went away like water in the sand (an old friend is better than two new ones) and the new thing was sent to the closet for storage - until better times. And now they came for her, did not even imagine that it would happen so quickly. And therefore the name would be even better suited not which is, but how to connect usb keyboard to tablet

Do-it-yourself clock on IN-14 lamps

I have long wanted to post an article on the manufacture do-it-yourself clocks on IN-14 lamps, or as they say, a steampunk watch.

I will try step by step and dwelling on the key points to state only the most important. The clock indication is clearly visible both day and night, and they themselves look very nice, especially in a good wooden case. In general, let's get started.

Those who are engaged in radio electronics at home are usually very inquisitive. Amateur radio circuits and homemade products will help you find a new direction in creativity. Perhaps someone will find an original solution to a particular problem. Some homemade products use ready-made devices, connecting them in various ways. For others, you need to completely create the circuit yourself and make the necessary adjustments.

One of the easiest crafts. More suitable for those who are just starting to tinker. If you have an old but working cell phone with a button to turn on the player, you can use it, for example, to make a doorbell to your room. Benefits of this call:

First you need to make sure that the selected phone is capable of producing a sufficiently loud melody, after which it must be completely disassembled. Basically, the parts are fastened with screws or brackets, which are carefully bent. When disassembling, you will need to remember what goes for what, so that later you can reassemble everything.

The player's power button is soldered on the board, and two short wires are soldered instead. These wires are then glued to the board so as not to tear off the solder. The phone is going. It remains to connect the phone to the call button through a two-wire wire.

Homemade for cars

Modern cars are equipped with everything you need. However, there are times when homemade devices are simply necessary. For example, something broke, gave to a friend, and the like. Then the ability to create electronics with your own hands at home will be very useful.

The first thing you can intervene in without fear of damaging the car is the battery. If at the right time charging for the battery was not at hand, you can quickly assemble it yourself. This will require:

The transformer from the tube TV is ideal. Therefore, those who are fond of homemade electronics never throw away electrical appliances in the hope that they will someday be needed. Unfortunately, two types of transformers were used: with one and with two coils. To charge the battery at 6 volts, anyone will go, and for 12 volts, only with two.

The wrapping paper of such a transformer shows the winding leads, the voltage for each winding, and the operating current. To power the filaments of electronic lamps, a voltage of 6.3 V with a large current is used. The transformer can be redone by removing unnecessary secondary windings, or left as is. In this case, the primary and secondary windings are connected in series. Each primary is designed for a voltage of 127 V, therefore, by combining them, they get 220 V. The secondary ones are connected in series to get 12.6 V at the output.

Diodes must be capable of withstanding at least 10 A. Each diode requires a heat sink of at least 25 square centimeters. They are connected to a diode bridge. Any electrical insulating plate is suitable for fastening. A 0.5 A fuse is included in the primary circuit, and 10 A in the secondary circuit. The device does not tolerate a short circuit, therefore, when connecting the battery, the polarity must not be confused.

Simple heaters

In the cold season, it may be necessary to warm up the engine. If the car is parked where there is electricity, this problem can be solved with a heat gun. For its manufacture you will need:

asbestos pipe;
nichrome wire;
fan;
switch.

The diameter of the asbestos pipe is selected according to the size of the fan to be used. The performance of the heater will depend on its power. Pipe length is everyone's preference. You can assemble a heating element and a fan in it, you can only have a heater. When choosing the latter option, you will have to think about how to let the air flow to the heating element. This can be done, for example, by placing all components in a sealed enclosure.

Nichrome wire is also selected by the fan. The more powerful the latter, the larger diameter nichrome can be used. The wire is twisted into a spiral and placed inside the pipe. Bolts are used for fastening, which are inserted into pre-drilled holes in the pipe. The length of the spiral and their number are chosen empirically. It is desirable that the coil does not heat up red-hot when the fan is running.

The choice of fan will determine how much voltage you need to apply to the heater. When using a 220 V electric fan, you will not need to use an additional power source.

The entire heater is connected to the mains through a cord with a plug, but it must have its own switch. It can be either just a toggle switch or an automatic one. The second option is more preferable, it allows you to protect the overall network. To do this, the tripping current of the machine must be less than the tripping current of the room machine. A switch is also needed to quickly turn off the heater in case of malfunctions, for example, if the fan does not work. Such a heater has its drawbacks:

harm to the body from asbestos pipes;
noise from a running fan;
the smell of dust falling on a heated coil;
fire hazard.

Some problems can be solved by applying another homemade product. Instead of an asbestos pipe, you can use a coffee can. So that the spiral does not close on the jar, it is attached to a textolite frame, which is fixed with glue. A cooler is used as a fan. To power it, you will need to assemble another electronic device - a small rectifier.

Homemade products bring to the one who deals with them not only satisfaction, but also benefit. With their help, you can save electricity, for example, by turning off electrical appliances that you forgot to turn off. For this purpose, you can use a time relay.

The easiest way to create a timing element is to use the charge or discharge time of a capacitor through a resistor. Such a chain is included in the base of the transistor. The diagram will require the following details:

high capacity electrolytic capacitor;
p-n-p type transistor;
electromagnetic relay;
diode;
variable resistor;
fixed resistors;
DC source.

First you need to determine what current will be switched through the relay. If the load is very powerful, you will need a magnetic starter to connect it. The starter coil can be connected via a relay. It is important that the relay contacts can operate freely without sticking. According to the selected relay, a transistor is selected, it is determined with what current and voltage it can work. You can focus on KT973A.

The base of the transistor is connected through a limiting resistor to a capacitor, which, in turn, is connected through a bipolar switch. The free contact of the switch is connected through a resistor to the minus power supply. This is necessary to discharge the capacitor. The resistor acts as a current limiter.

The capacitor itself is connected to the positive bus of the power supply through a variable resistor with a large resistance. By selecting the capacitance of the capacitor and the resistance of the resistor, you can change the delay time interval. The relay coil is shunted by a diode that turns on in the opposite direction. This circuit uses KD 105 B. It closes the circuit when the relay is de-energized, protecting the transistor from breakdown.

The scheme works as follows. In the initial state, the base of the transistor is disconnected from the capacitor, and the transistor is closed. When the switch is turned on, the base is connected to the discharged capacitor, the transistor opens and supplies voltage to the relay. The relay operates, closes its contacts and supplies voltage to the load.

The capacitor begins to charge through a resistor connected to the positive terminal of the power supply. As the capacitor charges, the base voltage begins to rise. At a certain voltage value, the transistor closes, de-energizing the relay. The relay disconnects the load. To make the circuit work again, you need to discharge the capacitor, for this the switch is switched.