Press and hold for 2 sec. button III of the key fob, after which the trunk will open. If the system is armed (the doors are locked), then it will be disarmed, the doors will be unlocked, the starter lock will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the car alarm system.
When opening the trunk:
Checking the system status [Button (IV)]
If you need to check the system status, shortly press the IV button of the keyfob-communicator. Information about the system state will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.
When checking the status of the SCHER - KHAN V car alarm system:
When checking the state of the car security system, the current time indicator shows the temperature in the car. Temperature can be displayed in either ° F or ° C.
The temperature inside the car is 10 ° C.
Repeated short pressing of the IV button of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.
The voltage on the car battery is 13.9V.
Panic or JackStop ™ (anti-capture) mode [Button (IV) -]
By pressing the button IV of the key fob for 2 sec. The car alarm system will enter "Panic" or JackStop ™ mode (anti-hijacking) - programmable function 1-4 .. If the system was disarmed, it will be armed, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the SCHER - KHAN V car security system will enter the armed mode until it is disarmed by the key fob or by the emergency shutdown mode. The "Panic" mode can be stopped by a short press of the I button. The "Panic" and JackStop ™ modes are used in case of danger or when it is necessary to draw attention to the car.
When Panic and JackStop ™ modes are activated:
Differences in the "Panic" and JackStop ™ algorithms (depending on the selected value of the programmable function 1-4):
| . | ||
button IV for 2 sec. |
button IV for 2 sec. |
|
The siren sounds for 1.5 minutes. |
The siren sounds for 1.5 minutes. |
|
Engine lock type |
Starter lock |
Ignition lock (lock is disabled during automatic start) |
Starter lock |
Turns on immediately |
Not used |
Ignition lock |
Not used |
Turns on immediately if the ignition is off. Turns on after 30 sec. after 2 sec. pressing the IV button if the ignition is on |
ATTENTION!
JackStop Mode™ can only be used in an emergency. It is not a standard, constantly used STTS mode, since it provides for stopping the engine while driving. When choosing one or another mode of the automobile alarm SCHER- KHAN V consult a specialist.
Turn off siren signals [Button (1 + 11)]
By briefly pressing the buttons I + II of the key fob simultaneously, you can turn on or turn off the siren signals. In this case, the key fob signals and signals alarm will work as usual. The siren activation is indicated by the presence of the symbol 
on the keyfob display.
When the siren signals are turned on:
When the siren signals are turned off:
VALET Mode [Button (I + III)]
To disable the security functions of the SCHER-KHAN 5 car alarm system and when transferring the car to a service station for service, you can use the VALET mode. To do this, shortly press the buttons I + III of the remote control.
In the VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press the I button.
The VALET mode is indicated on the display by the symbol 
To exit the VALET mode, shortly press the I + III buttons of the keyfob
When VALET mode is on:
When VALET mode is turned off:
Disabling the two-level shock sensor [Button (I + III)]
You can disable the two-level shock sensor of the SCHER - KHAN 5 car security system. Press and hold for 2 seconds at the same time. buttons 1+ III of the keyfob, as a result the sensors will be turned on or off. The sensor disconnection is indicated by the symbol on the keyfob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal is left in the car).
When disabling the shock sensor:
When you turn on the shock sensor of the SCHER - KHAN 5 car alarm:
The shock sensor is called two-level, because it has two levels of response from the impact on the car.
In case of a weak blow, the car security system warns with 4 short siren beeps and 4 flashes of the alarm. Key fob - the communicator beeps short, the vehicle strike symbol flashes on the display. In case of strong impact, the system goes into alarm mode for 30 seconds.
Central locking control for turning the ignition on and off [Button (I + IV)]
By briefly pressing the buttons I + IV of the keyfob simultaneously, you can enable or disable automatic control central locking(CZ) to turn the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors are closed, the hood / trunk are closed. The locks are unlocked immediately when the ignition is turned off. The activation of the function is indicated by the presence of a symbol on the key fob display.
When turning on the central locking control function from ignition:
When turning off the central locking control function from the ignition:
Passive arming [Button (II + III)]
The passive arming function can be turned on / off by short pressing of buttons II + III of the key fob. When passive arming is on, the car security system automatically enters the armed mode after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarm and / or siren signals every 10 seconds. If within 30 sec. the doors (hood / trunk) were opened, the system will enter the armed mode after 30 seconds. after closing the doors (hood / trunk).
When passive arming is enabled:
When disabling passive arming:
Setting the timer to automatically start the car engine [Button (II + IV)]
Briefly press the buttons II + IV of the remote control to enable or disable the engine start by timer. The indication of the start of the engine by timer is the presence of the "TIMER" label; on the keyfob display. The system provides two timer engine start modes. The first mode allows you to start the engine every day at a predetermined time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the cabin in countries with hot climates). The two modes cannot be used at the same time, the mode you need can be selected by programmable function 2–3.
To automatically start the engine by timer at the required time (24 hours), it is necessary to reserve this mode. For this:
1. Press buttons II + IV and turn off the label - TIMER
2. Select start time (table)
3. Press the II + IV buttons and turn off the TIMER
Execution steps |
Button number or combination of buttons |
Duration of pressing |
Performed function (mode) |
Entering the keyfob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob |
|||
Enabling the timer setting mode. The readings of the previously set time are blinking, confirmed by the keyfob sound signal |
|||
Changing the clock value |
|||
Changing the value of minutes |
|||
Exit the keyfob functions programming mode. Confirmed by a sound signal from the keyfob |
In order to enable or disable the engine start by timer every 2 hours, briefly press the buttons II + IV of the car alarm key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.
When starting the engine by timer:
When turning off the engine start by timer:
Note: Automatic start of the engine by timer every 24 hours is useful for daily starting the engine at a certain time if your car is parked outside the range of the car alarm key fob.
ATTENTION!
The time for starting a car engine by a timer of 24 hours can be shifted up to ± 2 minutes per day.
TURBO mode [Button (II + IV)]
If the car has a Turbo engine, then it is not recommended to stop it immediately after long-term operation at high speeds. The engine must idle for a while to cool the turbine. For this, the SCHER - KHAN MAGICAR V system provides a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, shortly press the buttons III + IV of the remote control.
When TURBO mode is on:
When TURBO mode is turned off:
To activate the mode at the end of the trip, do the following:
1. Place the transmission lever in neutral or P.
2. Turn the key in the ignition switch from ON to OFF. The car engine will continue to run after that for another 2 minutes.
3. Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash.
Now you can put the car alarm system in the car security mode. In this case, the engine will run until 2 minutes have elapsed. interval. When the car is armed, the door, hood / trunk sensors, driver call sensor are armed immediately, and the shock sensor will start working after the engine stops. The engine will be stopped immediately when the door, hood / trunk sensor is triggered and the system will go into alarm. If necessary, you can urgently stop the engine by pressing for 2 sec. button II of the keyfob.
Example of notation:
I - quick (0.5 sec.) Pressing the button
I - long (2 sec.) Button press
(I + II) - fast (0.5 sec.) Simultaneous pressing of buttons (combination of buttons)
(I + II) - long (2 sec.) Simultaneous pressing of buttons (combination of buttons)
Control channel number |
Button number |
Pressing duration |
Performed function (mode) |
| 1 | Arming / disarming Activate / deactivate call mode Stop alarm mode Activate / deactivate starter / ignition lock | ||
| 2 | Switch on the function - "Hands free" - the first operating mode (symbol does not flash) | ||
| 3 | Switch on the "Hands-free" "second operating mode (symbol flashes) | ||
| 4 | Switch off the function - "Hands free" - (the symbol goes out) | ||
| 5 | Recording and playback of a fragment on the voice module (Option) | ||
| 6 | Additional channel 1 control | ||
| 7 | Additional channel 2 control | ||
| 8 | Checking system status | ||
| 9 | Starting and stopping the engine from the key fob | ||
| 10 | Open trunk | ||
| 11 | "Panic". To stop press button I | ||
| 12 | Siren on / off | ||
| 13 | Mode -Valet "enable / disable | ||
| 14 | Automatic central lock control by ignition switch on / off | ||
| 15 | Automatic arming enable / disable | ||
| 16 | Timer start on / off | ||
| 17 | Mode - Turbo - enable / disable | ||
| 18 | Shock sensor enable / disable | ||
| 19 | Entering the programming menu 1 | ||
| 20 | Entering programming menu 2 |
Note:
With a long 2 sec. Pressing the I button sequentially changes the operating modes of the car alarm in the order (1)> (2)> (3)> (1)…. In mode (2) the "Hands-free" function has a long operating range - the symbol flashes.
Setting the time on the keyfob-communicator display
Setting the current time is required before using the system or when changing the keyfob battery. Follow the steps in the table below.
Execution steps |
Pressing duration |
Performed function (mode) |
|
Entering the keyfob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob |
|||
Enabling the mode of setting the current time. The current time is blinking, confirmed by the keyfob beep |
|||
Changing the clock value |
|||
Changing the value of minutes |
|||
Exit the keyfob functions programming mode. Confirmed by a sound signal from the keyfob |
ATTENTION!
Setting the exact time is necessary condition for correct work automatic engine start by timer.
Setting the modes of the keyfob-communicator.
Vibration call, owner call, "° F" or "° C" temperature display standard
To set the required operating mode of the car alarm key fob, follow the steps in accordance with the table below.
Execution steps |
Button number or combination of buttons |
Pressing duration |
Good day. Today we will consider an automobile SCHER-KHAN alarm system MOBICAR / Sherkhan Mobicar. This brand of signaling for cars includes the latest achievements in the field of car theft protection.
Purpose of car alarms
Signalka Sherkhan Magikar 5 has a special dedicated radio channel for signal control. The key fob switch has the ability to exchange signals with the process control unit at a distance of up to 1.5 km.
Magikar 5 can perform the following functions:
- block the engine with protection of system components;
- start the engine automatically, taking into account some parameters;
- provide sound activity for guards hidden from access.
All the features of the security system
Front self-installation you should study the connection diagram well. Even if everything is connected correctly, you still need to test and debug. Without this, not all functions can be used. It is also recommended to study separately the functions of the key fob, processor unit and technical specifications.
All the features of a key fob with an LCD screen
The body of the device is plastic with a liquid crystal screen. Has 4 control keys. The device performs the following functions:
- Information display on LCD display
- Accompanying keychain commands (audio, econ)
- Vibration accompaniment
- Warning range 1500 m
- System control range 1500 m
- Automatic LCD backlight
- Low battery indication
- Auto battery voltage indication
- Temperature display in the vehicle interior
- Time display
- Remote engine start
- Automatic engine start by alarm
- MAGIC CODE ™
- Separate buttons for arming and disarming
- Additional code for disarming confirmation
- Sound and visual reminder modes of receiving alarm message
- Battery AAA
The main functions of Sherkhan 5:
- Security code. Code protection is provided by SCHER-KHAN 5 Magic Code. All signals are encrypted.
- Control of executed commands. You can control the execution of commands through audio or video accompaniment.
- Charge level indication. The indicator shows the battery charge level.
- Engine running time. It is possible to watch how long the internal combustion engine has been running after autorun, the current time.
- Reminder of the running engine.
- Temperature display in the vehicle interior.
- Alarm reminder.
- Icon for manual remote start of the internal combustion engine.
- Working capabilities of the processor.
What car alarm is better: Senmax, Starline with auto start.
After the exchange of signals from the key fob and the processor, the signaling processor Sherkhan 5 issues the following commands:
- starting the internal combustion engine in automatic mode when one of the 2 modes of operation of the transmission unit is selected: "automatic" or mechanics.
- setting the interval for starting in offline mode. You can select 2, 4, 8 or 24 hours, or you can set it to start at a specific temperature in the vehicle interior or coolant.
- setting a command for forced start of the internal combustion engine.
- monitoring the operating mode of the motor.
- setting the engine start according to a given algorithm, taking into account the type of engine, operating time of the starter, etc.
- setting of personal identification codes of the Sherkhan alarm in case of loss of a key or key fob.
- there is the ability to set up security after starting the engine, the priority of opening is the driver's door.
- service functions: turning off the light with a delay, arming the car on the alarm in automatic mode without a key fob.
Video
How to set autostart of the engine by temperature on the Sher-Khan Magicar 5 alarm?
- it only has a start on the discharge of the battery !!!
- Attention! Impossible automatic start engine temperature only or only low battery voltage. The condition for triggering by time is mandatory.
Attention! During programming, the system must be disarmed and the ignition in the car must be turned off. The Hands-free mode is also disabled and the door is preferably open so that there is no re-arming during programming.
1) Configuring autostart by time (every 2, 4 or 8 hours)
b) To activate the autostart mode by time, press the IV button 13 times in succession (the siren emits a beep after each button press; that is, press once, hear a beep, press a second time - we hear a beep, and so on 13 times)
c) Wait for the siren to sound 13 times in a row.
d) Then select the required autostart time button II - 8 hours, III - 4 hours or IV - 2 hours.2) Setting autostart by temperature (when reaching t in the cabin -15, -25, +60)
For the autorun to work correctly, when the temperature is reached, you need to perform 3 steps:
2. Switch on temperature control (mode 1-21 in II, III or IV)
a) Recall that entering the function programming mode is carried out by long pressing the I + II buttons.
b) To activate the autostart mode by temperature, press the IV button 21 times in succession (the siren emits a beep after each button press; that is, press once, hear a beep, press a second time - we hear a beep, and so on 21 times)
c) Wait for the siren to sound 21 times in a row.
d) Then select the required autostart temperature button II - (-15), III - (by -25) or IV - (+60).
e) After that, you need to turn on the timer from the remote control. Press II + IV briefly at the same time, the display will show “timer”. If it was activated (lit) before programming, it must not be switched off (also II + IV) and switched on again.3) Configuring autostart on-board voltage
The implementation of the delayed start-up until the moment the battery is discharged to 11.5 V is carried out as follows:
1. Enable start by time (mode 1-13 in II, III or IV) see 1) a), b), c)
a) Entering the function programming mode by long pressing the I + II buttons.
b) To activate the voltage autostart mode, press the IV button 20 times in succession (the siren emits a beep after each button press; that is, press once, hear a beep, press a second time - we hear a beep, and so on 20 times)
c) Wait until the siren beeps 20 times in a row.
d) This will enter the programming mode of the Timer starts limiting function by battery voltage.
e) After that it is necessary to press button II to activate the mode.Engine warm-up time:
To set the engine warm-up time, set function 1-12 to position II.
In more detail, then you need to do the following:
a) Enter the function programming mode by long pressing the I + II buttons.
b) To set the engine warm-up time, press the IV button 12 times in succession (the siren emits a sound signal after each button press)
c) Wait until the siren beeps 12 times in a row.
d) Then we select the required duration of the start - button I - 5 minutes, button II - 15 minutes, III - 25 minutes or IV - 45 minutes.Make sure the system is disarmed and locked prior to programming.
- You set the desired temperature by programming the center. block and on the keychain you put the start on the timer, it seems like this.
V Lately various anti-theft systems are in great demand in the market. One of the most popular systems is the alarm system, which has an optimal ratio of functionality and cost. If you are looking for a really good gadget of this type, then excellent option will become "Sherkhan Magikar 5".
This device has excellent functionality, and also works reliably and stably. Thanks to the instructions, you can easily learn about the capabilities of this model, as well as learn all the features of operation.
You can easily use "Sherkhan Magikar 5" from a distance, because you have a special key fob that is responsible for communication between the user and the security system. The device is capable of working at a distance of up to 1.5 kilometers. The key fob is also equipped with a high-quality liquid crystal display, which makes it easy to read information.
With "Sherkhan Magikar 5" you can activate the motor only by a command, which is given by the user through the remote control to the internal timer of the device. When the engine is activated, the temperature in the passenger compartment, the condition of the battery and other parameters are neglected.
Device advantages
An important advantage is the versatility of the Sherkhan Magikar 5 alarm, because you can easily install it on cars with any type of gearbox, with engines running on any fuel. The main thing is that the on-board network is able to create a voltage of 12 V.
Users like the work of "Sherkhan Magikar 5" due to the fact that this device is really functional. With this device, you can protect a wide variety of parts of the car. In addition, manufacturers have done a good job of protecting the processor unit, antenna, and all kinds of sensors. They fully comply with the international IP-40 standard. All alarm parts are mounted right in your car, while the installation does not require much effort and time.
The siren of IP-65 standard, which is equipped with "Sherkhan Magikar 5", also works just fine: the signal is powerful, it works in a timely manner. In order for the sound signal to work as correctly as possible, the siren is mounted in the engine compartment of the car. At the same time, you need to make sure that there was no exhaust manifold or high-voltage systems next to it.
How to get started
It should be noted that when purchasing "Sherkhan Magikar 5", the device does not have a battery, since it was placed separately for the most convenient transportation. Thus, the charge will not be consumed even before you started using the alarm. For normal operation, the battery must be inserted into the correct compartment. To do this, you should take away the fixing plate, which holds the battery cover of the device in a certain position, and then move the compartment cover itself to the side opposite to the antenna.
You should now be able to install the battery in its proper place. At the same time, it is important to ensure that the polarity is selected correctly (you can easily verify this with the help of graphic pointers). When in doubt, simply place the battery with the negative pole towards the antenna. As soon as the battery is in its place, "Sherkhan Magikar 5" will notify you with a sound melody. Now you just have to close the lid and install the latch.
Already during the battery installation procedure, you can make sure that "Sherkhan Magikar 5" is made really high quality, because even to the touch the materials are durable and reliable.
Security mode
In order to turn on the security mode, first you need to turn off the engine and close all the doors and trunk of the car. So, you should press the "1" button on the control key fob. Immediately after that, the security device automatically activates the security mode on all elements of the car: the starter will be locked until you remove the lock yourself, and the door locks will also be locked.
To make sure that "Sherkhan Magikar 5" has successfully entered the security mode, the system should show you a number of signals:
- One-time siren activation;
- One-time operation of the emergency light signal;
- The LED indicator will start blinking, the blinking frequency will be 1 time per second;
- Synchronous five-time blinking of headlights;
- A single short signal from the key fob itself.
Sensor operation
If the indicator light is flashing, it means that the security system is monitoring the doors, trunk and other parts of the car through which it can be entered. "Sherkhan Magikar 5" additionally checks all sensors and continuously monitors them, while the motorist can relax, because his car is in good hands!
The device allows you to connect the delay control function for the lighting in the passenger compartment. If it is activated, the triggers are also controlled. Half a minute after the car has been armed, the shock sensor will start its work.
Warning Signals
It is important for the motorist to be vigilant and attentive to the car. For example, under no circumstances should the doors, trunk or hood be left open. "Sherkhan Magikar 5" will signal you about your inattention with a siren, three-time alarm and three-time signal on the key fob.
To make it easier for you to find the part of the car that you left open, its image will be highlighted on the display. True, it is displayed on the screen only for 5 seconds, after which it will be replaced by the inscription "FALL", which also indicates the inattention of the motorist.
If you have activated any sensor, then, unlike other communications of the device, it will not be closed, the security system will allow it to work until the user deactivates it.
Passive transition to security mode
In order for you not to forget to put the device in the security mode, "Sherkhan Magikar 5" can do it automatically. To do this, you just need to change the activation parameter for this function. With automatic arming, it will be activated half a minute after you closed the last door on your car. In this case, the key fob will constantly signal you that after a specified time the security mode will be activated. If, in 30 seconds, you open one of the doors, then the countdown will start over. Activation of passive protection is indicated by the inscription "Passive" on the key fob screen.
Alarm mode
"Sherkhan Magikar 5" works without any interruptions and errors, therefore, when the door is opened, the alarm mode is automatically activated, which lasts exactly 30 seconds, and if the cause of the alarm is eliminated, the security system will return to standard mode. If the cause is not corrected, then you will have another 8 cycles of 30 minutes to do it. If even after 4 minutes you could not eliminate the disturbing factor, the security system will automatically switch to the armed mode.
Signal triggering features
In the event that a strong physical impact was exerted on the machine, and the shock sensor is triggered, it will work for 5 seconds in an alarm mode with a strong sound signal and alarm operation. If the physical impact was weak, then the motorist will hear 4 short signals. So you will always know when someone touched your car or tried to get into it!
