Press and hold for 2 sec. button III of the key fob, after which the trunk will open. If the system is armed (the doors are locked), then it will be disarmed, the doors will be unlocked, the starter lock will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the car alarm system.
When opening the trunk:
Checking the system status [Button (IV)]
If you need to check the system status, shortly press the IV button of the keyfob-communicator. Information about the system state will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.
When checking the status of the SCHER - KHAN V car alarm system:
When checking the state of the car security system, the current time indicator shows the temperature in the car. Temperature can be displayed in either ° F or ° C.
The temperature inside the car is 10 ° C.
Repeated short pressing of the IV button of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.
The voltage on the car battery is 13.9V.
Panic or JackStop ™ (anti-capture) mode [Button (IV) -]
By pressing the button IV of the key fob for 2 sec. The car alarm system will enter "Panic" mode or JackStop mode™ (anti-tampering) - programmable function 1-4 .. If the system was disarmed, it will be armed, the door locks will be locked. The siren will sound for 90 seconds, alarm- flash for 90 sec. The "Panic" mode stops the automatic engine start mode. After 90 sec. the SCHER - KHAN V car security system will enter the armed mode until it is disarmed by the key fob or by the emergency shutdown mode. The "Panic" mode can be stopped by a short press of the I button. The "Panic" and JackStop ™ modes are used in case of danger or when it is necessary to draw attention to the car.
When Panic and JackStop ™ modes are activated:
Differences in the "Panic" and JackStop ™ algorithms (depending on the selected value of the programmable function 1-4):
| . | ||
button IV for 2 sec. |
button IV for 2 sec. |
|
The siren sounds for 1.5 minutes. |
The siren sounds for 1.5 minutes. |
|
Engine lock type |
Starter lock |
Ignition lock (lock is disabled during automatic start) |
Starter lock |
Turns on immediately |
Not used |
Ignition lock |
Not used |
Turns on immediately if the ignition is off. Turns on after 30 sec. after 2 sec. pressing the IV button if the ignition is on |
ATTENTION!
JackStop ™ can only be used in an emergency. It is not a standard, constantly used STTS mode, since it provides for stopping the engine while driving. When choosing one or another mode of the automobile alarm SCHER- KHAN V consult a specialist.
Turn off siren signals [Button (1 + 11)]
By briefly pressing the buttons I + II of the key fob simultaneously, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. The siren activation is indicated by the presence of the symbol 
on the keyfob display.
When the siren signals are turned on:
When the siren signals are turned off:
VALET Mode [Button (I + III)]
To disable the security functions of the system car alarms SCHER- KHAN 5 and when transferring the car to a service station for service, you can use the VALET mode. To do this, briefly press the buttons I + III of the remote control.
In the VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press the I button.
The VALET mode is indicated on the display by the symbol 
To exit the VALET mode, shortly press the I + III buttons of the keyfob
When VALET mode is on:
When VALET mode is turned off:
Disabling the two-level shock sensor [Button (I + III)]
You can disable the two-level shock sensor of the SCHER - KHAN 5 car security system. Press and hold for 2 seconds at the same time. buttons 1+ III of the keyfob, as a result the sensors will be turned on or off. The sensor disconnection is indicated by the symbol on the keyfob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal is left in the car).
When disabling the shock sensor:
When you turn on the shock sensor of the SCHER - KHAN 5 car alarm:
The shock sensor is called two-level, because it has two levels of response from the impact on the car.
In case of a weak blow, the car security system warns with 4 short siren beeps and 4 flashes of the alarm. Key fob - the communicator beeps short, the vehicle strike symbol flashes on the display. In case of strong impact, the system goes into alarm mode for 30 seconds.
Central locking control for turning the ignition on and off [Button (I + IV)]
By briefly pressing the buttons I + IV of the keyfob simultaneously, you can enable or disable automatic control central locking(CZ) to turn the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors are closed, the hood / trunk are closed. The locks are unlocked immediately when the ignition is turned off. The activation of the function is indicated by the presence of a symbol on the key fob display.
When turning on the central locking control function from ignition:
When turning off the central locking control function from the ignition:
Passive arming [Button (II + III)]
The passive arming function can be turned on / off by short pressing of buttons II + III of the key fob. When passive arming is on, the car security system automatically enters the armed mode after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarm and / or siren signals every 10 seconds. If within 30 sec. the doors (hood / trunk) were opened, the system will enter the armed mode after 30 seconds. after closing the doors (hood / trunk).
When passive arming is enabled:
When disabling passive arming:
Setting the timer to automatically start the car engine [Button (II + IV)]
Briefly press the buttons II + IV of the remote control to enable or disable the engine start by timer. The indication of the start of the engine by timer is the presence of the "TIMER" label; on the keyfob display. The system provides two timer engine start modes. The first mode allows you to start the engine every day at a predetermined time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the cabin in countries with hot climates). The two modes cannot be used at the same time, the mode you need can be selected by programmable function 2–3.
To automatically start the engine by timer at the required time (24 hours), it is necessary to reserve this mode. For this:
1. Press buttons II + IV and turn off the label - TIMER
2. Select start time (table)
3. Press the II + IV buttons and turn off the - TIMER
Execution steps |
Button number or combination of buttons |
Duration of pressing |
Performed function (mode) |
Entering the keyfob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob |
|||
Enabling the timer setting mode. The readings of the previously set time are blinking, confirmed by the keyfob sound signal |
|||
Changing the clock value |
|||
Changing the value of minutes |
|||
Exit the keyfob functions programming mode. Confirmed by a sound signal from the keyfob |
In order to enable or disable the engine start by timer every 2 hours, briefly press the buttons II + IV of the car alarm key fob. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.
When starting the engine by timer:
When turning off the engine start by timer:
Note: Automatic start of the engine by timer every 24 hours is useful for daily starting the engine at a certain time if your car is parked outside the range of the car alarm key fob.
ATTENTION!
The time for starting a car engine by a timer of 24 hours can be shifted up to ± 2 minutes per day.
TURBO mode [Button (II + IV)]
If the car has a Turbo engine, then it is not recommended to stop it immediately after long-term operation at high speeds. The engine must idle for a while to cool the turbine. For this, the SCHER - KHAN MAGICAR V system provides a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, shortly press the buttons III + IV of the remote control.
When TURBO mode is on:
When TURBO mode is turned off:
To activate the mode at the end of the trip, do the following:
1. Place the transmission lever in neutral or P.
2. Turn the key in the ignition switch from ON to OFF. The car engine will continue to run after that for another 2 minutes.
3. Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash.
Now you can put the car alarm system in the car security mode. In this case, the engine will run until 2 minutes have elapsed. interval. When the car is armed, the door, hood / trunk sensors, driver call sensor are armed immediately, and the shock sensor will start working after the engine stops. The engine will be stopped immediately when the door, hood / trunk sensor is triggered and the system will go into alarm. If necessary, you can urgently stop the engine by pressing for 2 sec. button II of the keyfob.
GOST R 41.97-99 (Uniform provisions concerning the approval of vehicle alarm systems (TCS) and motor vehicles with respect to their alarm systems (TCS))
GOST R 50009-2000 (Electromagnetic compatibility. Security alarm technology. Requirements and test methods)
Thank you for purchasing the SCHER-KHAN MAGICAR V two-way car security system.
Constant research and development of our company embodies the most advanced ideas and serves to meet all the needs of users of our systems.
Car alarm SHERKHAN MagiKar 5 is a complex electronic equipment of the car. From its functioning and correct installation depends on the safety of your life, health and road conditions, the quality of work of nearby radio electronic equipment and communications. Entrust the installation of the system only to specialized service stations. Periodically check the correct functioning of the system during operation.
PLEASE READ CAREFULLY!
ATTENTION!
When purchasing, check that the warranty card is filled in correctly.
The manufacturer and supplier of the system are not responsible for any disregard of the points in the installation and operation manuals, as well as for mistakes made during installation.
If you have any problems related to the functioning of the system, please immediately contact the service center for diagnostics or consultation.
Installation of the SCHER-KHAN MagiKar-5 car alarm should be carried out by qualified specialists. Car alarm is tricky technical device, involving connection to the electrical circuits of the car associated with the operation of the engine.
If an icon appears on the key fob display warning about the low battery of the key fob, take measures to replace the battery in advance. We recommend that you keep a new spare battery in your vehicle, keeping its original packaging.
PURPOSE
The SCHERKHAN MAGICAR V car alarm is a car alarm with the ability to be controlled by radio using a communicator with a LCD display. The system exchanges information between the communicator keyfob and the processor unit at a distance of up to 1500 m. SHERKHAN MagiKar 5 has a function of automatic engine start by commands from a key fob or by commands from an internal timer. The SCHER-KHAN MAGICAR V system is designed to operate on gasoline or diesel vehicles with a fuel injection system and a 12V on-board network voltage. Protection of the processor unit, shock sensor, call sensor, antenna unit is made according to the standard and provides for installation in the passenger compartment. The siren is designed for and can be installed in the engine compartment, away from the exhaust manifold and high voltage systems.
Contents of delivery
When purchasing the system, make sure the delivery is complete. The specified delivery set is basic and can be supplemented in accordance with the wishes of the buyer with additional components.
Operation manual 1
Installation Guide 1
SCHER-KHAN MAGICAR V 1 processor unit
Keyfob communicator 1
Shock sensor with cable CN5 1
Vehicle call sensor with CN6 cable 1
Antenna unit 1
Light emitting diode (LED) 1
Temperature sensor 1
Interlock relay with socket 1
Siren 1
Hood / trunk limit switch 1
6 pin power connector with cable and fuse CN1 1
6 pin power connector with cable CN2 1
9-pin control connector CN3 1
4-wire cable for connecting antenna unit CN7 1
2-pin connector for control of additional channels CN8 1
Car call sensor sticker 1
Antenna unit sticker 1
Glass sticker 2
Additional components SCHER-KHAN MAGICAR
Immobilizer bypass module SCHER-KHAN BP-2
Keyfob-communicator SCHER-KHAN MAGICAR V (with display) *
SCHER-KHAN MAGICAR V keyfob (without display) *
* The processing unit can remember the codes of only three remote controls.
Keychain communicator functions
- Multifunctional, 4-button LCD keyfob communicator
- Protection against interception of code messages MAGIC CODE
- Audiovisual confirmation of executed commands
- Vibration bell
- Loud beeps
- Ultra-long distance communication up to 1500 m with the processor unit
- Automatic display backlight
- Low battery indication
- Vehicle battery voltage display
- Temperature display in the vehicle interior
- Time display
- Indication of engine running time in automatic mode
- Remote engine start
- Programming the engine start time (accurate to the minute)
- Sound and visual reminder mode of receiving alarm message
- Operative, with a remote control, programming of all system functions
- Economical food (one AAA cell)
Functions of the processor unit
- Automatic engine start of vehicles with automatic or manual transmission
- Starting system operation with both gasoline and diesel engines
- The operation of the starting system with engines with a turbine
- Starting the engine on command from the remote control
- Automatic engine start every 2 hours
- Automatic engine start at a predetermined time every 24 hours
- Tracking engine start by signals from the generator or by noise in the on-board network
- Personal code for access to the car interior in case of key loss
- Power output for controlling the central locking of the car
- Power output for unlocking the trunk lock
- Alarm control power output (two circuits)
- Latching relay type programming
- Automatic arming (programmable function)
- Sound warning before automatic arming
- Automatic return to armed mode if the door has not been opened
- Sound warning before automatic return to the armed mode
- Security mode without siren signals
- Two universal programmable control channels for additional devices
- Possibility to connect negative and positive door sensors
- Negative trunk sensor input
- Locking and unlocking doors when starting and stopping the engine
- Possibility of arming with and without siren confirmation signals
- Open door alarm warning (programmable function)
- Panic or JackStop mode
- Highly sensitive two-level shock sensor with sensitivity adjustment
- Hands-free function for automatic arming / disarming when the owner moves away / approaches the car
- Dual-mode hands-free function
- Side lights warning not switched off
TECHNICAL SPECIFICATIONS
Alarm types:
Influence on the main and additional electrical equipment of the car
| STSTS controls power supply to: | Maximum channel current |
|---|---|
| Starter or ignition interlock circuit | Imax = 0.2 A |
| Port side alarm circuit | Imax = 10 A |
| Starboard alarm circuit | Imax = 10 A |
| Ignition circuit | Current Imax = 30 A |
| Accessory chain | Current Imax = 30 A |
| Starter chain | Current Imax = 30 A |
| Ignition circuit 2 | Current Imax = 0.2 A |
| Additional siren | Current Imax = 2 A |
| Relay for control of unlocking of electric door locks or unlocking of the standard system of the Central locking (CL) of the car | Current Imax = up to 15 A |
| Control relay for locking the electric door locks or locking the standard Central locking system (CL) of the car | Current Imax = up to 15 A |
| Trunk lock electric control relay | Current Imax = 10 A |
| Accessory Control Channel 1 | Current Imax = 0.2 A |
| Accessory Control Channel 2 | Current Imax = 0.2 A |
| Channel for disarming the STSTS standard installed on the car | Current Imax = 0.2 A |
Control methods
- Remote radio frequency transmitter (key fob) at a frequency of 433.92 MHz ± 0.2% at a power not exceeding 10 mW
- From the ignition key
- Automatically by signals from sensors
Protection of electrical circuits
Fuses. (Automotive time delay fuses according to the wiring diagram)
Spheres of protection
Other parameters
Batteries
* The table shows the average. The service life of the key fob battery depends on the intensity of use of the key fob and the quality of the battery, the operating modes of the key fob.
..ATTENTION!
Use only high quality batteries. The use of a poor quality battery can lead not only to a reduction in the service life of the keychain, but also to damage it.
KEY FOB-COMMUNICATOR SCHER-KHAN MagiKar-5
Preparing the communicator keychain for work
Before using the key fob, you must bring it into working condition, because during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before use. Remove the key fob before using it. To do this, open the battery compartment cover lock, press the cover and slide it out to the side opposite to the antenna. Take out the battery. Remove the insulating strip between the battery and the collector plate. Insert the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is installed with the negative terminal towards the antenna. Close the battery compartment cover. The keychain is ready for use.
Symbols on the display of the communicator
| Timer start indicator | |
| TURBO mode enable indicator | |
| Indicator of activation of the passive arming mode | |
| Hands-free indicator | |
| Siren signal on indicator | |
| Shock sensor off indicator | |
| Vibration chime on indicator | |
| Indicator for turning on automatic central locking control by ignition | |
| Open door indicator | |
| Open trunk / bonnet indicator | |
| Shock sensor alarm indicator (optional sensor) | |
| Car owner call indicator | |
| Running engine indicator | |
| Ignition on indicator in security mode, indicator of non-switched off side lights | |
| Indicator of operation of the transmitter of the key fob-communicator | |
| Battery discharge indicator of the keychain communicator | |
| VALET mode indicator | |
| Indicator for locking and unlocking locks. Arming status indicator | |
 |
Indicator of hours, car battery voltage, temperature in the passenger compartment, engine warm-up time at automatic start |
Purpose of the keyfob-communicator buttons
Example of notation:
I - quick (0.5 sec.) Pressing the button
I- - long (2 sec.) Pressing the button
(I + II) - fast (0.5 sec.) Simultaneous pressing of buttons (combination of buttons)
(I + II) - - long (2 sec.) Simultaneous pressing of buttons (combination of buttons)
| Control channel number | Button number | Pressing duration | Performed function (mode) |
|---|---|---|---|
| 1 | I | 0.5 sec. |
|
| 2 | I- (1) | 2 sec. | Switch on the hands-free function first operating mode (symbol does not flash) |
| 3 | I- (2) | 2 sec. | Switch on the hands-free function in the second operating mode (symbol flashes) |
| 4 | I- (3) | 2 sec. | Switch off the "Hands-free" function (symbol goes out) |
| 5 | (III + IV) - | 2 sec. | Recording and playback of a fragment on the voice module (Option) |
| 6 | II | 0.5 sec. | Additional channel 1 control |
| 7 | III | 0.5 sec. | Additional channel 2 control |
| 8 | IV | 0.5 sec. | Checking system status |
| 9 | II- | 2 sec. | Starting and stopping the engine from the remote control |
| 10 | III- | 2 sec. | Open trunk |
| 11 | IV- | 2 sec. | "Panic". To stop press button I |
| 12 | (I + II) | 0.5 sec. | Siren on / off |
| 13 | (I + III) | 0.5 sec. | "Valet" mode enable / disable |
| 14 | (I + IV) | 0.5 sec. | Automatic central lock control by ignition switch on / off |
| 15 | (II + III) | 0.5 sec. | Automatic arming enable / disable |
| 16 | (II + IV) | 0.5 sec. | Timer start on / off |
| 17 | (III + IV) | 0.5 sec. | Turbo mode enable / disable |
| 18 | (I + III) - | 2 sec. | Shock sensor enable / disable |
| 19 | (I + II) - | 2 sec. | Entering the programming menu 1 |
| 20 | (I + IV) - | 2 sec. | Entering programming menu 2 |
Note:
With a long 2 sec. Pressing the I button changes the modes sequentially in the order (1)> (2)> (3)> (1)…. In mode (2) the "Hands-free -" function has a long operating range - the symbol flashes.
Setting the time on the display of the communicator keyfob
Setting the current time is required before using the system or when changing the remote control battery. Follow the steps in the table below.
| Execution steps | Pressing duration | Performed function (mode) | |
|---|---|---|---|
| STEP 1 | (II + III) - | 2 sec. | |
| STEP 2 | I | 0.5 sec. | Enabling the mode of setting the current time. The current time is blinking, confirmed by a sound signal from the remote control |
| STEP 3 | I | 0.5 sec. | Changing the clock value |
| II | 0.5 sec. | Changing the value of minutes | |
| STEP 4 | (II + III) - | 2 sec. |
ATTENTION!
Setting the exact time is necessary condition for correct work automatic engine start by timer.
Setting the modes of the key fob-communicator, Vibration call, owner call, temperature display standard "° F" or "° C"
To set the required operating mode of the key fob, follow the steps in accordance with the table below.
Note: STEP 2 must be completed no later than 15 seconds. after STEP 1.
Arming [Button (I)]
Close the doors, hood, trunk. Briefly press the button I of the remote control. The system will enter the security mode, the door locks will lock, the starter (ignition) interlock will turn on until the system is disarmed.
When arming:
Enabling sensors:
Note:
If, when arming, you hear three signals from the remote control, and on the display for 5 seconds. the image of an open door or trunk is flashing, this means that the door, hood / trunk is open in the car. The door, hood / trunk sensor will be immediately armed when its functionality is restored.
The bonnet area is not shown separately on the display, the bonnet sensor must be connected to the trunk sensor wire.
Disarming [Button (I)]
When the system is in the armed mode, shortly press the I keyfob button. The SHER-KHAN MagiKar-5 alarm will be disarmed, the door locks will be unlocked, the starter (ignition) lock will be disabled.
When disarming:
...HANDS-FREE function [Button (I) -]
ATTENTION!
The "Hands-free" mode works only when using a communicator-communicator with an LCD display; when using optional keyfobs without a display, this mode is not available.
By pressing button I of the communicator key fob for 2 sec. you can turn Hands-Free on or off. When the "Hands-free" function is enabled, the system automatically enters the security mode when you move away from the car with a communicator-key fob at a distance of 15-35 m *. or disarmed and unlocks the door locks when approaching. The function has two modes of operation:
In the first mode, the mark on the display does not flash and the range of the function is minimal.
In the second mode, the label on the display with the inscription "AUTO" blinks and the operating range is maximum.
The change of operating modes takes a long time 2 sec. by pressing the I button in the following order: (Function enabled, mode 1)> (Function enabled, mode 2)> (Function disabled)> (Function enabled, mode 1)….
Arming / disarming will be accompanied by a melodic signal from the communicator key fob.
Constant use of the "Hands-free" function is not recommended, as its use drastically reduces the battery life of the key fob.
* Note:
The distance from the unit to the communicator key fob, at which the system decides to arm or disarm, can vary and depends on a number of objective reasons: the relative position of the antennas of the communicator key fob and the antenna unit, the presence of metal objects near the antennas, radio interference on the air, weather etc. …
When Hands-Free is enabled:
The change of the mode is accompanied by one signal from the communicator keychain.
When you deactivate the HANDS-FREE function:
....Starting the engine on command from the remote control [Button (II) -]
To start the engine, press button II of the remote control for 2 seconds. The system will enter the security mode, the door locks will be locked, the car engine will start. After the engine has started, information on the time remaining until the engine stops operating in automatic mode will appear on the display of the communicator key fob. The engine running time is programmable and can be 15/25/45/5 minutes (programmable function 2-4). To start driving. You need to open the door, insert the ignition key into the lock and turn it to the "ON" position. To do this, you have 20 seconds, after this time the system will transfer control to the ignition switch, if you have not turned on the ignition, the engine will be stopped.
If the launch did not happen the first time, the system will try again. The system makes no more than three startup attempts, after which it goes into standby mode. If the car engine does not start after the last attempt, contact a service station to diagnose your car.
At the time of launch:
The SCHERKHAN MAGICAR V car alarm will not start the engine if:
- Ignition is on
- The car's engine is already running
- Door or hood / trunk open
- The redundancy mode for vehicles with manual transmission has not been fulfilled
On successful launch:
Note: If the car's engine is started automatically, the current time indicator shows the time remaining until the engine is stopped. The time is displayed in countdown mode. Time display format in this mode: [XX min: XX sec.]
When the engine stops automatically:
Trunk opening [Button (III) -]
Press and hold for 2 sec. button III of the remote control, after which the trunk will open. If the system is armed (the doors are locked), then it will be disarmed, the doors will be unlocked, the starter lock will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the system.
When opening the trunk:
Checking the system status [Button (IV)]
If you need to check the system status, shortly press the IV button of the keyfob-communicator. Information about the system state will be shown on the key fob-communicator display, as well as confirmed by siren and alarm signals.
When checking the system status:
When checking the system status, the current time indicator shows the temperature in the vehicle interior. Temperature can be displayed in either ° F or ° C.
The temperature inside the car is 10 ° C.
Repeated short pressing of the IV button of the key fob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.
The voltage on the car battery is 13.9V.
Panic or JackStop mode (anti-capture) [Button (IV) -]
By pressing the button IV of the remote control for 2 sec. The system will enter the "Panic" mode or the JackStop mode (protection against capture) - programmable function 1-4 .. If the system was disarmed, it will enter the armed mode, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the system will enter the armed mode until it is disarmed by the key fob or by the emergency shutdown mode. The "Panic" mode can be stopped by a short press of the I button. The "Panic" and JackStop modes are used in case of danger or when it is necessary to draw attention to the car.
When the "Panic" and JackStop modes are activated:
Differences in the "Panic" and JackStop algorithms (depending on the selected value of the programmable function 1-4):
ATTENTION!
JackStop can only be used in an emergency. It is not a standard, constantly used CTCTС mode. it provides for stopping the engine while driving.
When choosing one or another mode, consult a specialist.
Silencing off the siren signal [Button (I + II)]
By briefly pressing the buttons I + II of the remote control simultaneously, you can turn on or turn off the siren signals. In this case, the key fob signals and alarms will work as usual. The siren activation is indicated by the presence of a symbol on the key fob display.
When the siren signals are turned on:
When the siren signals are turned off:
VALET Mode [Button (I + III)]
To disable the security functions of the system and when transferring the car to a service station for service, you can use the VALET mode. To do this, briefly press the buttons I + III of the remote control.
In the VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press the I button.
The VALET mode is indicated on the display by the symbol
To exit the VALET mode, shortly press the I + III buttons of the remote control
When VALET mode is on:
When VALET mode is turned off:
.....Disabling the two-level shock sensor [Button (I + III)]
You can turn off the two-level shock sensor. Press and hold for 2 seconds at the same time. buttons I + III of the remote control, as a result the sensors will be turned on or off. The sensor disconnection is indicated by the symbol on the key fob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal is left in the car).
When disabling the shock sensor:
When the shock sensor is turned on:
The shock sensor is called two-level, because it has two levels of response from the impact on the car.
In case of a weak impact, the system warns with 4 short siren beeps and 4 flashes of the alarm. Key fob - the communicator beeps short, the vehicle strike symbol flashes on the display. In case of strong impact, the system goes into alarm mode for 30 seconds.
Central locking control for turning the ignition on and off [Button (I + IV)]
By briefly pressing the buttons I + IV of the key fob at the same time, you can turn on or off the automatic control of the central lock (CZ) by turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors are closed, the hood / trunk are closed. The locks are unlocked immediately when the ignition is turned off. The activation of the function is indicated by the presence of a symbol on the key fob display.
When turning on the central locking control function from ignition:
When turning off the central locking control function from the ignition:
Passive arming [Button (II + III)]
The passive arming function can be turned on / off by short-term pressing of the buttons П + Ш of the remote control. When passive arming is on, the system automatically enters the armed mode after 30 seconds. after closing the last door or after disarming with the key fob. Alarm SHER-KHAN MagiKar-5 warns of passive arming with alarm signals and (or) a siren every 10 seconds. If within 30 sec. the doors (hood / trunk) were opened, the system will enter the armed mode after 30 seconds. after closing the doors (hood / trunk).
When passive arming is enabled:
When disabling passive arming:
Setting the timer for automatic engine start [Button (II + IV)]
Briefly press the buttons II + IV of the remote control to turn on or off the engine start by timer. The indication of starting the engine by timer is the presence of the "TIMER" mark on the key fob display. The system provides two timer engine start modes. The first mode allows you to start the engine every day at a predetermined time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the cabin in countries with hot climates). The two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3.
To automatically start the engine by timer at the required time (24 hours), it is necessary to reserve this mode. For this:
| Execution steps | Button number or combination of buttons | Pressing duration | Performed function (mode) |
|---|---|---|---|
| STEP 1 | (II + III) - | 2 sec. | Entering the key fob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob |
| STEP 2 | II | 0.5 sec. | Enabling the timer setting mode. The readings of the previously set time are blinking, confirmed by a sound signal from the remote control |
| STEP | I | 0.5 sec. | Changing the clock value |
| II | 0.5 sec. | Changing the value of minutes | |
| STEP 4 | (II + III) - | 2 sec. | Exit the keyfob functions programming mode. Confirmed by a sound signal from the key fob |
In order to enable or disable the engine start by timer every 2 hours, shortly press buttons II + IV of the remote control. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.
When starting the engine by timer:
When turning off the engine start by timer:
Note: Automatic start of the engine on a timer every 24 hours is useful for daily starting the engine at a certain time if your car is parked outside the range of the remote control.
ATTENTION!
The time for starting the engine on a timer of 24 hours can be shifted up to ± 2 minutes per day.
TURBO mode [Button (II + IV)]
If the car has a Turbo engine, then it is not recommended to stop it immediately after long-term operation at high speeds. The engine must idle for a while to cool the turbine. For this, the SCHER-KHAN MAGICAR V system provides a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, shortly press the buttons III + IV of the remote control.
When TURBO mode is on:
When TURBO mode is turned off:
To activate the mode at the end of the trip, do the following:
Now you can arm the system. In this case, the engine will run until 2 minutes have elapsed. interval. When the car is armed, the door, hood / trunk sensors, driver call sensor are armed immediately, and the shock sensor will start working after the engine stops. The engine will be stopped immediately when the door, hood / trunk sensor is triggered and the system will go into alarm. If necessary, you can urgently stop the engine by pressing for 2 sec. button II of the key fob.
Additional Channel 1 Control [(II) Button]
If your car is equipped with an electromechanical hood lock, an additional pre-heater or other service equipment, You can control the operation of these devices using the key fob. To do this, shortly press button II of the remote control. A short or long signal will appear at the output of additional channel 1 of the processor unit (programmable function 2-5). The siren and side light signals will differ when an additional channel is controlled, depending on the state of programmable function 2-5. If the channel is programmed for a long signal (Value 4 of the programmable function 2-5), the system will confirm its activation and deactivation by siren and alarm signals. If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel. The additional channel does not work in VALET mode and in alarm mode.
Note: If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel (programmable function 2-5)
Control of additional channel 2 [Button (III)]
If your car has an electromechanical hood lock, an additional pre-heater or other service equipment, you can control the operation of these devices using a remote control. To do this, briefly press button III of the remote control. A short or long signal will appear at the output of additional channel 2 of the processor unit (programmable function 2-6). The signals of the siren and side lights will differ when controlling an additional channel, depending on the state of programmable function 2-6. If the channel is programmed for a long signal (Value 4 of the programmable function 2-6), the system will confirm its activation and deactivation by siren and alarm signals. If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel. The additional channel does not work in VALET mode and in alarm mode.
Enabling an additional channel:
Switching off an additional channel:
Note: If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel (programmable function 2-6)
Alarm mode
If the door, hood / trunk is opened in the armed mode, the system will go into alarm mode for 30 seconds, alarm signals and sirens will last for 30 seconds. At the end of 30 sec. the system will return to armed mode. If the shock sensor alarm zone is triggered (strong impact), the system will go into alarm mode for 15 seconds, alarm signals and sirens will last for 15 seconds. At the end of 15 sec. the system will return to armed mode. When the shock sensor warning zone is triggered (weak impact), the system will not go into alarm mode, but will only issue a series of four short signals with a siren and an alarm. You can terminate the alarm mode by short pressing the I key fob button. In this case, the locks will not be unlocked, and the system will switch from alarm mode to armed mode.
In alarm mode:
Reminder mode
If the communicator key fob received an alarm signal from the door, hood / trunk sensors, shock sensor, call sensor and you did not notice this immediately, the key fob, after the alarm signal is transmitted, goes into the reminder mode (with short beeps and indication of the zone that caused the alarm mode) ... To terminate the reminder mode and check the state of the car, briefly press the IV button of the remote control or button I to exit the security mode and unlock the doors.
In reminder mode:
Note: The communicator keyfob does not go into reminder mode when it receives a warning signal from the shock sensor (weak impact)
Car owner call
If you need to call the car owner, knock with a hard object (coin, keys, etc.) near the call sensor. The call sensor LED will flash green. The function of calling the car owner is available immediately after arming. To stop the signals from the communicator keyfob, press the I keyfob button. To terminate the signals of the remote control communicator and check the condition of the car, shortly press the IV button.
When calling the car owner:
Access to the car without a key fob
Access to the car without a key fob may be required in a number of cases. For example, if the key fob is lost, if the battery in the key fob has run out, if you are relaxing on the beach and do not want to take the key fob with you (the key fob and keys are locked in the car). The SCHERKHAN MAGICAR V system provides this opportunity. To allow access only to you, the system uses a personal code consisting of four digits. The value of each digit of the code can vary from 1 to 9. Thus, the code can have a value from 1111 to 9999. The code is entered and recorded through the call sensor of the car owner.
Personal code entry:
In order for you to use this function, you must enter your code into the system memory. To do this, follow several steps:
If at any of the steps you made a mistake, then you need to record the code, starting from point 1.
Personal code entry:
The system allows five attempts to enter the code within 30 minutes. If the code was entered incorrectly, then its entry is blocked for 24 hours or until you disarm the system using the remote control.
Battery protection (warning about unplugged dimensions)
Alarm SHER-KHAN MagiKar-5 helps to protect the car battery from discharge. If you forgot to turn off the side lights, then when arming, the communicator keyfob will give a series of beeps for 5 seconds. At this time, the images of the lock and side lights will flash on the display. The warning beep will repeat every 30 seconds. three times.
Starter or ignition interlock
The system in the security mode will not allow starting the car engine. When an attempt is made to start the engine in the armed mode, the system will send an alarm signal to the communicator key fob. The ignition switch-on alarm will be indicated by the flashing of the side lights on the communicator key fob, sound and vibration signals. The engine blocking mode is selected when the system is installed at a service station and depends on the values of two programmable functions 1-4 and 1-8. You can find out more about blocking the engine of your car at the place of installation of the system. When starter lock is selected, the system will prevent the car's starter from restarting if the engine is started in automatic mode.
Open door warning
The SCHERKHAN MAGICAR V car alarm warns of an open door (programmable function 1-2). When a custom function value is selected, the alarm flashes if the car door is open.
Protection of the radio channel from interception of the code
The system has special protection for the commands transmitted by the key fob. Each time you press the button on the system key fob, the code message changes according to a special algorithm. This is done to protect the system from interception of the code and its selection (intellectual hacking of the security system). The code protection algorithm is specially developed for the SCHER-KHAN MAGICAR system and is unique, not used in one security system of other brands.
Motor protection in auto start mode
The system continuously monitors engine operation in automatic start mode. If the engine stops before the end of the warm-up cycle (engine malfunction or out of fuel), then no later than 20 seconds. the system processor unit will turn off the ignition. Automatic restart of the engine will not be possible until the malfunction is eliminated. For vehicles with a manual transmission, it is necessary to execute the redundancy mode again.
Shock sensor sensitivity adjustment
You can adjust the sensitivity of the shock sensor depending on your requirements. A regulator is provided on the sensor to adjust the sensitivity. Turning the knob clockwise increases the sensitivity, and counterclockwise decreases it, until the sensor is turned off. Consult a service station for the location of the shock sensor, it should be easily accessible for adjustment.
Adjusting the sensitivity of the owner call sensor
You can adjust the sensitivity of the car owner call sensor depending on your requirements. To adjust the sensitivity, a step regulator with three positions is provided on the sensor. The extreme left position of the regulator corresponds to the minimum sensitivity of the sensor, the extreme right - to the maximum. The sensor should be located in the lower corner of the car's windshield.
Adjusting the volume of the siren confirmation signals
You can adjust the volume of the siren short beeps. To decrease the volume, you must cut the loop from the wire on the siren body. The system can be equipped with any siren in accordance with the wishes of the owner, including one where there is no adjustment option.
Redundancy Mode (Manual Transmission Only)
The standby mode prevents the engine from starting automatically if the manual transmission lever is not in neutral. Depending on your requirements, you can choose one of three backup algorithms (programmable function 1-6).
Algorithm 1
Algorithm 2
To perform redundancy (preparing the car for the subsequent automatic engine start), do the following:
Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnostics of the reasons for its failure is described below.
If at least one step from the above algorithm is not performed, then there will be no redundancy mode and automatic engine start will not occur. In this algorithm, redundancy will be disabled if the door, hood / trunk is open at the time the ignition is turned off.
Algorithm 3
To perform redundancy (preparing the car for the subsequent automatic engine start), do the following:
Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnostics of the reasons for its failure is described below.
If at least one step from the above algorithm is not performed, then there will be no redundancy mode and automatic engine start will not occur. In this algorithm, making a reservation requires you to press button II of the key fob each time before turning off the ignition (by turning the key in the ignition lock to the OFF position).
ATTENTION!
Close the sunroof and windows before exiting the vehicle. Do not leave people or animals in the vehicle while performing the redundant mode.
Do not automatically start the engine while people or animals are in the vehicle.
Leave the transmission lever in neutral at all times. Do not use automatic engine start on open top vehicles.
If the operation of the backup mode differs from the described algorithms or does not occur, immediately contact your service station for advice. Do not use the automatic engine start until the cause of the malfunction is eliminated.
PROGRAMMING NEW KEY FOBS
The system can memorize the codes of three key fobs. Follow two steps to program new keyfobs.
To exit programming mode, do not take any action for 4 seconds. after writing the code of the last remote control.
If after step 1 no action is taken, after 4 sec. the alarm will flash 2 times, the system will switch from the keyfob programming mode to the VALET mode.
Note:
Alarm SHER-KHAN MagiKar-5 has three memory cells for storing keyfob codes. If you try to record the fourth key fob, the code of the first recorded key fob will be deleted.
FUNCTION PROGRAMMING WITH KEY FOB
Programming the STTS functions using a key fob consists of four steps.
Note:
If, when choosing the function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all actions, starting from STEP 1.
Note:
If you hear one long siren signal, it means the system exits the function programming mode. To continue programming, it is necessary to repeat all actions, starting from STEP 1.
ATTENTION!
If it is necessary to change more than one function from the Menu selected by you, then the selection of each function to change must be started from STEP 1.
Programmable function menu
Menu # 1 [Button (I + II) -]
| P / p No. | Function | [Button (I)] Factory default | [Button (II)] | [Button (III)] |
|---|---|---|---|---|
| 1-1 | Delay before starter rotation after ignition on. Should be increased for a diesel vehicle. | 4 sec. | 10 sec. | |
| 1-2 | Open door warning | Not | There is | |
| 1-3 | Pulse duration of central lock control. Should be increased for pneumatic central locking system | 0.8 sec. | 4 sec. | |
| 1-4 | Panic or JackStop mode (anti-robbery) | "Panic" (Starter lock) | JackStop (Ignition lock) | |
| 1-5 | Central lock control for ignition on and off | Turned off | Turned off | |
| 1-6 | A method of starting redundancy. (Only for manual transmission) | Automatically whenever the ignition is turned off | Automatically whenever the ignition is turned off, provided the doors are closed | Only manual mode, before turning off the ignition to back up, press button II for 2 seconds. |
| 1-7 | Starter rotation time | Standard | Standard + Minimum | Standard + Maximum |
Feature note 1-4: This function allows you to select the "Panic" mode or the JackStop mode (anti-robbery):
Setting all programmable functions of menu # 1 to factory defaults
Menu # 2 [Button (I + IV) -]
Setting all programmable functions of menu # 2 to factory defaults
There are two steps to complete the factory defaults for programmable functions.
Example of notation:
I - quick (0.5 sec.) Pressing the button
I - long (2 sec.) Button press
(I + II) - fast (0.5 sec.) Simultaneous pressing of buttons (combination of buttons)
(I + II) - long (2 sec.) Simultaneous pressing of buttons (combination of buttons)
Control channel number |
Button number |
Pressing duration |
Performed function (mode) |
| 1 | Arming / disarming Activate / deactivate call mode Stop alarm mode Activate / deactivate starter / ignition lock | ||
| 2 | Switch on the function - "Hands free" - the first operating mode (symbol does not flash) | ||
| 3 | Switch on the "Hands-free" "second operating mode (symbol flashes) | ||
| 4 | Switch off the function - "Hands free" - (the symbol goes out) | ||
| 5 | Recording and playback of a fragment on the voice module (Option) | ||
| 6 | Additional channel 1 control | ||
| 7 | Additional channel 2 control | ||
| 8 | Checking system status | ||
| 9 | Starting and stopping the engine from the key fob | ||
| 10 | Open trunk | ||
| 11 | "Panic". To stop press button I | ||
| 12 | Siren on / off | ||
| 13 | Mode -Valet "enable / disable | ||
| 14 | Automatic central lock control by ignition switch on / off | ||
| 15 | Automatic arming enable / disable | ||
| 16 | Timer start on / off | ||
| 17 | Mode - Turbo - enable / disable | ||
| 18 | Shock sensor enable / disable | ||
| 19 | Entering the programming menu 1 | ||
| 20 | Entering programming menu 2 |
Note:
With a long 2 sec. Pressing the I button sequentially changes the operating modes of the car alarm in the order (1)> (2)> (3)> (1)…. In mode (2) the "Hands-free" function has a long operating range - the symbol flashes.
Setting the time on the keyfob-communicator display
Setting the current time is required before using the system or when changing the keyfob battery. Follow the steps in the table below.
Execution steps |
Pressing duration |
Performed function (mode) |
|
Entering the keyfob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob |
|||
Enabling the mode of setting the current time. The current time is blinking, confirmed by the keyfob beep |
|||
Changing the clock value |
|||
Changing the value of minutes |
|||
Exit the keyfob functions programming mode. Confirmed by a sound signal from the keyfob |
ATTENTION!
Setting the correct time is a prerequisite for the correct operation of the automatic engine start timer.
Setting the modes of the keyfob-communicator.
Vibration call, owner call, "° F" or "° C" temperature display standard
To set the required operating mode of the car alarm key fob, follow the steps in accordance with the table below.
Execution steps |
Button number or combination of buttons |
Pressing duration |
V Lately various anti-theft systems are in great demand in the market. One of the most popular systems is the alarm system, which has an optimal ratio of functionality and cost. If you are looking for a really good gadget of this type, then excellent option will become "Sherkhan Magikar 5".
This device has excellent functionality, and also works reliably and stably. Thanks to the instructions, you can easily learn about the capabilities of this model, as well as learn all the features of operation.
You can easily use "Sherkhan Magikar 5" from a distance, because you have a special key fob that is responsible for communication between the user and the security system. The device is capable of working at a distance of up to 1.5 kilometers. The key fob is also equipped with a high-quality liquid crystal display, which makes it easy to read information.
With "Sherkhan Magikar 5" you can activate the motor only by a command, which is given by the user through the remote control to the internal timer of the device. When the engine is activated, the temperature in the passenger compartment, the condition of the battery and other parameters are neglected.
Device advantages
An important advantage is the versatility of the Sherkhan Magikar 5 alarm, because you can easily install it on cars with any type of gearbox, with engines running on any fuel. The main thing is that the on-board network is able to create a voltage of 12 V.
Users like the work of "Sherkhan Magikar 5" due to the fact that this device is really functional. With this device, you can protect a wide variety of parts of the car. In addition, manufacturers have done a good job of protecting the processor unit, antenna, and all kinds of sensors. They fully comply with the international IP-40 standard. All alarm parts are mounted right in your car, while the installation does not require much effort and time.
The siren of IP-65 standard, which is equipped with "Sherkhan Magikar 5", also works just fine: the signal is powerful, it works in a timely manner. In order for the sound signal to work as correctly as possible, the siren is mounted in the engine compartment of the car. At the same time, you need to make sure that there was no exhaust manifold or high-voltage systems next to it.
How to get started
It should be noted that when purchasing "Sherkhan Magikar 5", the device does not have a battery, since it was placed separately for the most convenient transportation. Thus, the charge will not be consumed even before you started using the alarm. For normal operation, the battery must be inserted into the correct compartment. To do this, you should take away the fixing plate, which holds the battery cover of the device in a certain position, and then move the compartment cover itself to the side opposite to the antenna.
You should now be able to install the battery in its proper place. At the same time, it is important to ensure that the polarity is selected correctly (you can easily verify this with the help of graphic pointers). When in doubt, simply place the battery with the negative pole towards the antenna. As soon as the battery is in its place, "Sherkhan Magikar 5" will notify you with a sound melody. Now you just have to close the lid and install the latch.
Already during the battery installation procedure, you can make sure that "Sherkhan Magikar 5" is made really high quality, because even to the touch the materials are durable and reliable.
Security mode
In order to turn on the security mode, first you need to turn off the engine and close all the doors and trunk of the car. So, you should press the "1" button on the control key fob. Immediately after that, the security device automatically activates the security mode on all elements of the car: the starter will be locked until you remove the lock yourself, and the door locks will also be locked.
To make sure that "Sherkhan Magikar 5" has successfully entered the security mode, the system should show you a number of signals:
- One-time siren activation;
- One-time operation of the emergency light signal;
- The LED indicator will start blinking, the blinking frequency will be 1 time per second;
- Synchronous five-time blinking of headlights;
- A single short signal from the key fob itself.
Sensor operation
If the indicator light is flashing, it means that the security system is monitoring the doors, trunk and other parts of the car through which it can be entered. "Sherkhan Magikar 5" additionally checks all sensors and continuously monitors them, while the motorist can relax, because his car is in good hands!
The device allows you to connect the delay control function for the lighting in the passenger compartment. If it is activated, the triggers are also controlled. Half a minute after the car has been armed, the shock sensor will start its work.
Warning Signals
It is important for the motorist to be vigilant and attentive to the car. For example, under no circumstances should the doors, trunk or hood be left open. "Sherkhan Magikar 5" will signal you about your inattention with a siren, three-time alarm and three-time signal on the key fob.
To make it easier for you to find the part of the car that you left open, its image will be highlighted on the display. True, it is displayed on the screen only for 5 seconds, after which it will be replaced by the inscription "FALL", which also indicates the inattention of the motorist.
If you have activated any sensor, then, unlike other communications of the device, it will not be closed, the security system will allow it to work until the user deactivates it.
Passive transition to security mode
In order for you not to forget to put the device in the security mode, "Sherkhan Magikar 5" can do it automatically. To do this, you just need to change the activation parameter for this function. With automatic arming, it will be activated half a minute after you closed the last door on your car. In this case, the key fob will constantly signal you that after a specified time the security mode will be activated. If, in 30 seconds, you open one of the doors, then the countdown will start over. Activation of passive protection is indicated by the inscription "Passive" on the key fob screen.
Alarm mode
"Sherkhan Magikar 5" works without any interruptions and errors, therefore, when the door is opened, the alarm mode is automatically activated, which lasts exactly 30 seconds, and if the cause of the alarm is eliminated, the security system will return to standard mode. If the cause is not corrected, then you will have another 8 cycles of 30 minutes to do it. If even after 4 minutes you could not eliminate the disturbing factor, the security system will automatically switch to the armed mode.
Signal triggering features
In the event that a strong physical impact was exerted on the machine, and the shock sensor is triggered, it will work for 5 seconds in an alarm mode with a strong sound signal and alarm operation. If the physical impact was weak, then the motorist will hear 4 short signals. So you will always know when someone touched your car or tried to get into it!
Excellent performance characteristics and high reliability is the signalization "Sherkhan Magikar 5". The operating instructions provide a detailed explanation of the principles of using this device and its main functions.
The purpose
The instruction "Sherkhan Magikar 5" indicates that this alarm can be remotely controlled by the user, which is assisted by an exclusive communicator key fob. The display is made of liquid crystal material and is therefore considered particularly reliable.
A specially built-in system regulates a single mechanism of interaction between the processor unit and the communicator key fob. The alarm can be controlled from a distance of 1500 m.
The engine starts after a special command has been given. It is usually directed along the key fob, the outside of the device, the internal timer. This does not take into account the temperature in the car, and the voltage level of the battery is also unimportant.
Advantages
Preparing the key fob for work
Before using the key fob, you need to make several manipulations, since there is no battery in it during transportation. It is located separately, and not in the intended compartment. This is necessary to conserve full charge. Removing the battery does not consume power, so there is no need to recharge the device.
To place the battery in the right place, you should carefully pull out the latch, which holds the battery cover of "Sherkhan Magikar 5" in its original position. In this case, malfunctions are excluded, since all structural elements are made with maximum quality. This applies to both cutting out parts and the material from which they are created.
After completing this step, you must move the cover itself to the side that runs opposite to the protruding antenna. The battery for power supply should be carefully inserted into the compartment. As with any battery, polarity is provided here, so the position of its sides can be determined only after reading the graphic drawing near this compartment.
If there are no signs, then the Sherkhan Magikar 5 signaling is placed with a minus sign in the direction where the antenna is located. After correct installation, a characteristic melody is heard, which indicates the completion of the necessary actions for the correct operation of the system. All you need to do is close the battery compartment cover, and then install the appropriate lock on it.
Arming
To activate the security mode, you must first turn off the ignition, and also close all compartments of the car to ensure the free operation of "Sherkhan Magikar 5". The instruction manual determines that then, with just one touch, the button under number 1 on the key fob is pressed. It is not necessary to hold it for a long time, a point and moderate touch is enough. The system will automatically switch all the necessary elements of the car into the security mode. The operating locks on the doors will be blocked, the starter will not work until the owner himself removes this mode.
When the car alarm "Sherkhan Magikar 5" is armed successfully, a person can trace some signals:
- The siren will sound once with a moderate whistle.
- The hazard warning light will also show itself once.
- The LED indicator will be connected, which will show that the car is under protection by means of measured flashing at a frequency of 1 time per second.
- The headlights will flash synchronously five times. Further, the image of the closed lock will remain on until the car is unlocked, and the headlights will go out.
- The key fob will give only one short signal.
Enabling sensors
When the LED starts to blink regularly, it means the activation of the system control over the state of all possible entrances and methods of entering the car, which cannot be allowed by "Sherkhan Magikar 5". The instruction manual informs that even the owner call and ignition control sensors are additionally checked and constantly monitored, which allows the owner to calmly do any of his business at this time.
If an additional function is connected, which is responsible for regulating the delay of the salon light, it will also provide for the control of triggers, which usually begin to be protected not immediately, but only after a certain amount of time has elapsed. activates work 30 seconds after the car is armed.
Warning
The instruction "Sherkhan Magikar 5" warns users against inattentive attitude to the car. Should not be left open doors, hood and luggage compartment. If this happened, then the person unexpectedly, instead of the usual behavior of the car when arming, hears a three-time signal from the key fob along with a siren. In this case, the alarm also flashes three times at once.
On the display, you can see an image of an object that the owner of the car forgot to close. This only happens for five seconds, so the user may not have time to see the desired item. At the same time, the text FALL appears on the display. This is a direct indication that you should find the uncovered element and cover it tightly.
"Sherkhan Magikar 5" instruction manual defines as a device top class, since it arms all vehicle communications, but bypasses the activated sensor. It will be automatically additionally guarded after the owner closes it. The bonnet area is not reflected in the general panel, as it refers to the trunk area.
Automatic transition to security mode
Passive arming is a separate function that can be activated or deactivated in Sherkhan Magikar 5. The autorun instruction provides - you just need to change the state of the selected function. If the owner decides to activate just such a mode, then immediately after the last door is closed, the timer is activated, and the security is turned on after 30 seconds.
When the countdown starts, the system constantly sends alerts that this mode will turn on. This happens every 10 seconds. If any door is opened at the specified time, the system will arm the system after a countdown of 30 seconds after the last door has been closed. It is possible to trace whether this function works by the word PASSIVE, which is always displayed in this case.
Alarm mode
When Sherkhan Magikar 5 is operating, malfunctions are unacceptable. When any door is opened, the system will automatically be in alarm mode for exactly 30 seconds. When this time is up, it will return to its standard state again.
If the cause that caused the alarm has not been eliminated by this time, the signal will sound every 30 seconds and continue for half a minute. This cycle is repeated eight times. If even then the reason for the violation of the usual mode is not canceled, the system returns to the armed mode, but provided that the active sensor is bypassed.
Features of work
If the shock sensor is triggered, that is, there is a strong impact on any part of the car, the "Sherkhan Magikar 5" alarm will be in the alarm mode for 5 seconds, during which a strong one is sent from the siren and the alarm.
In case of weak impact, that is, activation of the warning zone, also regulated by the shock sensor, 4 short ones will sound, which are generated by the "Sherkhan Magikar 5" car alarm. There were no malfunctions in this process, so the owner of the device can be confident in his own technique.
Many users appreciate the ease of use of "Sherkhan Magikar 5". How to disable the security mode? With a short single press on the key fob button number 2. If you program all the functions of the device correctly, the alarm system will become a reliable assistant in ensuring the safety of the car.
