Setting up the alarm key fob scher khan magicar 5. Scher-Khan Magicar V - user manual

The system can memorize the codes of three key fobs. Follow two steps to program new keyfobs.

1. Turn the ignition key three times from OFF to ON.

The alarm will flash once to confirm entering the programming mode.

2. Not later than 4 sec. after the flashing of the alarm, press the button I of the key fob, the code of which must be entered into the memory of the processor unit.

If after step 1 no action is taken, after 4 sec. alarm flashes 2 times, the system will switch from keyfob programming mode to VALET mode.

Note: the system has three memory cells for storing keyfob codes. If you try to write the fourth keyfob, the code of the first recorded keyfob will be deleted.

Sher-Khan 7.8

KEY FOB PROGRAMMING

The system can memorize the codes of three key fobs.

To write keyfob codes:

1) In the "disarmed" mode with the ignition on, press the button on the call sensor body for 2 seconds. Alarm will flash once

2) Within 5 sec. briefly press the call sensor button. The alarm will flash twice if the personal code PIN 1 is not used (programmable function 1-6 in the factory

value, see page 69) or once if using PIN 1 (programmable function 1-6 in optional value)

3) If PIN 1 is used, it is necessary to enter its value (“Entering the personal code PIN 1 in the keyfob programming mode”, items 5 to 8 on page 60). The alarm will flash twice

4) After 5 sec. the LED will light up blue, confirming the readiness to enter the keyfob codes

5) Within 5 sec. shortly press button I of the first remote control. In confirmation of the code recording, the alarm will flash 1 time. Then you can enter the code of the second and third keyfobs, after successfully entering the code of each new keyfob, the alarm will flash 1 time, after entering the code of the third keyfob, the alarm will flash twice and the system will exit the keyfob programming mode.

When writing the code of at least one new key fob, the codes of all key fobs previously recorded in the system memory will be deleted

To exit programming mode, do not take any action for 4 seconds. after writing the code of the last keyfob.

If after step 4 no action is taken, then after 5 sec. You will hear one siren signal *, the alarm will flash once, the system will switch from keyfob programming mode to VALET mode.

Sher-Khan Jungle, Vegas

PROGRAMMING NEW KEY FOBS

The system can memorize the codes of four key fobs.

To start programming new key fobs, you need to:

Disarm the system

Turn on the car ignition

In the case when the PIN code is not used (the factory value of the programmable function is 20), the following sequence of actions must be performed:

1) Within 5 seconds, shortly press the VALET button three times. The system will confirm the action taken with one flash of the alarm

2) Within the next 5 seconds, briefly press the button of the first remote control. The system will confirm the successful entry of the keyfob code with one flash of the alarm. The new keyfob code will be added to the processor unit memory. This will delete the keyfob code that was programmed first.

3) In the case when it is necessary to program the codes of several key fobs, it is necessary to sequentially press the button on each of them with a time interval between presses of at least 1 second and no more than 5 seconds. The system will confirm each press with one flash of the alarm.

If no action is taken within 5 seconds, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm

4) If four key fobs are programmed, then after pressing the button on the last of them, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm. In the event that fewer than four keyfobs are programmed and it is necessary to delete the codes of the previous keyfobs from the memory, press the button on any of the keyfobs several times until the system exits the programming mode (two flashes of the alarm)

In the case when a PIN code is used (value 2 of programmable function 20), for programming new

keyfobs, you must perform the following sequence of actions:

1) Entering the first digit of the PIN-code (factory value - "1"). To do this, shortly press the VALET button in a row the required number of times, corresponding to the first digit of the PIN-code. The time interval between clicks should be no more than 3 seconds. After that, do not perform any action for 3 seconds. After this time has elapsed, the system will confirm the entry of the first digit with one flash of the alarm

2) Entering the second digit of the PIN-code (factory value - "1"). To do this, shortly press the VALET button in a row the required number of times, corresponding to the second digit of the PIN-code. To enter the PIN code correctly, you must start entering the second digit no later than 3 seconds after the alarm flashes, confirming the entry of the first digit. The time interval between clicks should also be no more than

3 seconds. After entering the second digit, do not perform any action for 3 seconds. After this time has elapsed, the system will confirm the entry of the correct PIN-code values with one flash of the alarm. If two flashes of the alarm signal follow, it means that the PIN-code was entered incorrectly, while the system returns to the initial mode and it is impossible to update the keyfob codes.

After three unsuccessful attempts entering a PIN-code, this operation is blocked for 30 minutes

3) Within 5 seconds after confirming the correct PIN-code entry, shortly press the button of the first remote control. The system will confirm the successful entry of the keyfob code with one flash of the alarm. The new keyfob code will be added to the processor unit memory. This will delete the keyfob code that was programmed first.

4) When it is necessary to program the codes of several keyfobs, it is necessary to sequentially press the button on each of them with an interval of time between presses of at least 1 second and no more than 5 seconds. The system will confirm each press with one flash of the alarm. If no action is taken within 5 seconds, the system will automatically end the mode of programming new key fobs, which will be confirmed by two flashes of the alarm

5) If four remote controls are being programmed, after pressing the button on the last of them, the system will automatically end the mode of programming new remote controls, which will be confirmed by two flashes of the alarm. In the event that less than four keyfobs are programmed and it is necessary to delete the codes of the previous keyfobs from the memory, press the button on any of the keyfobs several times until the system exits the programming mode (two flashes of the alarm)

Sher-Khan 6

PROGRAMMING TECHNIQUE FOR NEW KEYROBS

ATTENTION!

The system has a secure algorithm for writing new key fobs,which excludes unauthorized recording of key fobs into memorysystems. To ensure the secrecy of the recording, do not forget to enter the codeemergency shutdown PIN 1.

The system can memorize the codes of three key fobs. To start programming, the system must be disarmed using the key fob or emergency using the PIN1 ignition lock or using the PIN2 call sensor. Also, on the keyfob being recorded, the Hands Free function must be turned off.

Follow four steps to program new keyfobs:

1. Turn the key in the ignition switch from OFF to ON three times. The alarm will flash once to confirm that the first step has been completed. Switch off the ignition.

2. Not later than 4 sec. after the flash of the alarm, turn on the ignition the number of times corresponding to the first digit of the personal code (factory value is "1"). Switch off the ignition. The alarm will flash once to confirm that the second digit is ready.

3. Not later than 4 sec. after the flash of the alarm, turn on the ignition the number of times corresponding to the second digit of the personal code (factory value is "1"). Switch off the ignition.

The alarm will flash once to confirm that the third digit is ready.

4. Not later than 4 sec. after the flashing of the alarm, press the button I of the key fob, the code of which must be entered into the memory of the processor unit. With an interval of no more than 4 seconds, you can press buttons 1 of the three key fobs, then the system will remember their codes. If it is necessary to write down the code of only one remote control, then shortly press the button I of this remote control three times.

To exit the programming mode, do not take any action for 4 seconds. after writing the code of the last keyfob.

Two flashes of the alarm will follow, confirming the exit from the keyfob codes programming mode.

Note:

The system has three memory cells for storing keyfob codes. When trying to write the fourth keyfob, the code of the first recorded keyfob

Alarm Sherkhan 5 with auto start refers to budget systems and is intended for use in cars, the voltage of which is 12 volts. The car alarm has two-way communication, which operates within a radius of 1500 m.

[Hide]

Scher-Khan Magicar 5 Alarm Feature

This model of the signaling can be installed on a car with a manual transmission or on an automatic machine. The security device is powered by a rechargeable battery.

Main functions

Options provided by the multifunctional communicator keyfob:

confirmation of the executed commands by means of sound or vibration;
protection of the communication channel from interception of code data, the system is called "Magic code";
playback of sound signals when the alarm mode is activated;
backlight of the liquid crystal screen of the device;
designation of the power supply charge inside the communicator;
determination of the voltage level in the electrical network of the vehicle;
designation of the temperature value in the car interior;
determination of the current time on the screen;
output of the operating time of the power unit, started automatically;
the ability to remotely start the engine of the machine;
setting the start time of the power unit with an accuracy of minutes;
reminder mode via sound or visual messages;
the ability to program all the options of the anti-theft installation.

Description of the options performed by the microprocessor module:

remote start of the power unit on vehicles with any type of transmission;
operation of the system on gasoline and diesel internal combustion engines, including those equipped with turbines;
the ability to start the power plant by a command sent from the communicator;
option to configure remote start by timer, every 2 hours, or by alarm every day;
the ability to monitor the state of the running motor in accordance with the signals sent from the generator set or noise in the power grid;
availability of a personal password to access the vehicle interior in case of key loss;
use of power outputs for control central locking, a luggage compartment door, as well as a light alarm;
setting of the blocking relay type - normally closed or normally open;
mode of automatic activation of the protective option;
sound warning before activating the automatic mode of protection;
re-activation of the protection function if the vehicle door has not been opened;
the ability to activate the protection mode without being accompanied by siren signals;
the presence of two universal programmable channels used to control additional equipment;
microprocessor module allows additional connection of positive and negative door controllers;
the presence of a separate input for installing a negative sensor in the luggage compartment;
the ability to close and open door locks when starting and stopping the power unit in automatic mode;
activation of the protection mode with or without confirmation signals;
option of warning light signaling of the car owner about open door, this mode must be programmed beforehand;
Panic function, allowing to activate the operation of the siren and light signaling on command;
the Hands-free option, which makes it possible to automatically enable or disable the protective function if the car owner approaches the car or moves away from it;
function of warning the driver about the included side lights.

The Autoazart channel briefly spoke about the options and capabilities of the Sherkhan Magikar 5 security complex.

Technical specifications

The main properties of the anti-theft installation:

the range of the communicator is up to 1500 meters in ideal terrain;
the keychain is powered by AAA batteries;
optimal operation of the anti-theft system is possible in the on-board network at 9-18 volts;
the current strength when the system is running is 20-35 mA;
the temperature range at which the security complex operates is from -40 to +85 degrees Celsius;
the total mass of the microprocessor module is 270 g.

Car owner alert signals are divided into several groups:

sound for the siren - when the alarm mode is activated, their duration is 30 seconds, the signals are played continuously;
optical for car headlights - signals with a power of 1 Hz and a duration of 30 seconds function on two channels and are reproduced intermittently;
using a radio channel - information is transmitted to the communicator and reproduced intermittently.

The exact range of the key fob depends on many factors:

power supply charge;
the presence of interference on the ground;
obstacles in the form of large structures, structures, transformer substations;
weather conditions.

Information is transmitted to the communicator over a secure channel using encryption.

All electrical circuits of the security complex are protected by means of safety, resistor devices and transistors. To prevent voltage surges and noise, the system is equipped with varistors. If, during the connection, errors related to polarity are made, this will not affect the operation of the signaling, since the power supplies are equipped with diode elements.

Contact controllers react to opening door locks or turning the key in the ignition switch. If such a sensor is triggered, the signal will play an alarm without the possibility of shutting down without a remote control. The security complex with auto start Sherkhan 5 also reacts to physical influences on the body and, when they are fixed, issues alarm signals.

The values of the currents for the protection of electrical circuits are given in the table.

Description of the power line	Amount of current
Blocking the operation of the ignition systems and the starter mechanism	0,2
Turning lights on the left side of the body	10
Turn signals on the right side of the car	10
Ignition system	30
Additional ACC circuit	30
Starter power line	30
Additional electrical circuit of the ignition system	0,2
Drive line of locks of the left front and rear doors	15
Electric circuit of the drive mechanism of the locks of the right front and rear doors	15
Additional channel for the lock installed on the tailgate	10
Additional first channel	0,2
Additional second channel	0,2
Communication channel with factory alarm	0,2

User guide

A key fob or an ignition key can be used to control the anti-theft complex. At correct setting this procedure is carried out using the panic button. Using the remote control, you can program functions and set a password for emergency shutdown or activation of the system.

Setting up a PIN

To set up a personal password, you need to enter the programming mode:

The vehicle is disarmed.
The door lock of the machine is opened.
The ignition is activated by installing and turning the key in the lock. The motor should not start.
The third and fourth keys are clamped on the communicator keyfob. The alarm will blink once with light devices, the siren will go off. If the signal is triple, this indicates an unsuccessful attempt to enter the password setting mode.
The first digit of the code is entered, for this the consumer is given four seconds after the siren signal. To set the values, use the communicator keys, the selected digit corresponds to the button. If the symbol is accepted successfully, the alarm will play the corresponding number of flashes and siren signals.
Subsequent digits are indicated identically, each car owner is given four seconds to enter. When the last character is entered, the system will automatically exit the setup mode. The car owner will be informed about this by a double siren signal and two flashes of light devices.
Then you can turn off the ignition and lock all the doors of the car.

To open a vehicle using the code, follow these steps:

The car alarm is deactivated.
The driver's door opens.
The key is inserted into the lock, the ignition is activated.
The car owner taps the call controller ten times. The time interval between impacts should be 1.5 seconds. With each subsequent impact, the diode element will blink red.
Each character of the password is configured by the method of strikes, their number must correspond to a digit. Confirmation of input is carried out every 1.5 seconds. When you indicate each digit, the diode will blink blue.
Similarly, each character of the password is indicated. In confirmation, the alarm will blink with lights and sound a siren.

If the car owner enters the PIN-code settings mode, the diode lamp will flash blue.

The channel "Videomax12345" spoke about the main settings and functions of the anti-theft system.

How to enable security mode?

You need to start the healed mode after turning off the ignition and closing all the door locks of the car. To complete the task, the first key on the remote control is clicked. This will block the door locks and starter mechanism.

When this function is activated, the following occurs:

the siren sounds once;
the lights of the car are blinking;
the diode indicator flashes on the unit at 1 second intervals;
the vehicle headlights blink five times on the communicator display and the locked padlock indicator appears;
the remote control emits a melodic signal.

The indicator in the form of a locked padlock is displayed on the communicator until the protection mode is disabled. When the security is turned on, the alarm constantly monitors and analyzes the readings issued by the controllers. 30 seconds after the protection is turned on, the sensitivity sensor is activated. If the power unit remains running, the arming procedure is the same. All doors are locked and the first key on the pager is clicked.

But the sensitivity controller will remain off until the ignition is working. Security mode indication will be similar. 30 seconds after turning off the power unit, a signal check will occur.

User Sergey Gorin showed several ways to control the security mode of the Magikar 5 signaling.

System check

The fourth key is used to diagnose the state of the anti-theft device. After pressing it, the car alarm analysis data will be displayed on the communicator screen. Information about the check will be confirmed by siren signals, as well as light signaling.

System shutdown

To disarm the system, use the second key of the communicator. In confirmation, the siren will play one signal, the car lights will go off. The headlights of the car will blink on the pager screen, an indicator with an open lock will appear.

Keychain - communicator

Before using the remote control, you need to install a power supply.

To do this, a protective cover is removed on the back of the communicator, into which the battery is inserted observing the polarity. Then the lid is closed.

Indicator designation

Key designations on the remote control display

Description of symbols on the communicator screen:

A - timer operation of the power unit;
В - turbo timer option;
С - passive security activation mode;
D - the option of automatic activation of the guard without clicking on the keys;
E - activated siren;
F - sensitivity controller is disabled;
G - the communicator has the vibration alert function enabled;
H - door locks control after activation of the ignition system;
J - open luggage compartment door;
K - the power unit is started in automatic start mode;
L - the state of the anti-theft installation;
M - open door locks;
N - information field for displaying clock data, as well as temperature conditions during automatic start;
О - the service mode of functioning of the Jack is enabled;
R - the light alarm is on on the car or the parking lights are not turned on;
Q - activation of the sensitivity controller;
R - communicator power supply icon;
S - signal level.

Keychain main functions

To adjust the main parameters and set functions, use the button combinations shown in the table.

Key number	Pressing duration	System function
1	0.5 sec	Used to activate options: activation and deactivation of the security mode; activation and deactivation of the call mode; stopping the alarm mode; activation and deactivation of the blocking of the starter mechanism and the ignition system
1	2 seconds	Activation of the Hands-free option in the first operating mode, the indicator does not blink
1	2 sec	Activation of the Hands-free function in the second operating mode with a blinking indicator
1	2 sec	Disable the Hands-free option, the indicator disappears
3+4	2 sec	Simultaneous click will result in recording and playback of the fragment on the audio module
2	0.5 sec	Additional first channel control function
3	0.5 sec	Option to control an additional second channel
4	0.5 sec	Diagnostics of the state of the anti-theft installation
2	2 sec	The function allows you to start and stop the power unit on command from the communicator
3	2 sec	Command to open the tailgate
4	2 sec	Panic mode, the first key is used to disable
1+2	0.5 sec	Command to activate mute siren
1+3	0.5 sec	Combination for disabling and activating the Jack service mode
1+4	0.5 sec	Command for automatic control of the central lock by ignition
2+3	0.5 sec	Automatic activation and deactivation of protection mode
2+4	0.5 sec	Timer start option
3+4	0.5 sec	Command to activate and deactivate Turbo mode
1+3	2 sec	Command to disable and enable the sensitivity controller
1+2	2 sec	Button for entering programming mode 1
1+4	2 sec	Command to activate programming mode 2

How to bring the key fob into working order?

The procedure for binding a new communicator is as follows:

A key is inserted into the lock, after which the ignition is switched on and off three times. Light signaling should work once, which indicates entering the configuration mode.
Over the next four seconds, you need to click on the first button on the communicator.
Then the pager code is entered into the memory of the microprocessor module.

The car owner can record no more than three communicators. Therefore, when setting up the fourth device, information about the first is deleted from the microprocessor memory. To exit the settings mode, do not touch the key fob for four seconds.

Channel "MasikBonLive" spoke about the independent binding of the new communicator to the microprocessor signaling module.

Configuring autorun

There are four options for setting the autostart option on the Sherhan system:

by command:
by time;
by air temperature;
to reduce the voltage in the on-board network of the car.

Configuring launch on command

The option is activated as follows:

The transmission lever is set to the neutral position, and the handbrake is activated. If the car is equipped with an automatic transmission, then the gearshift knob is moved to the parking position.
All door locks of the vehicle are locked.
Button 2 on the communicator is held down for two seconds.
The ignition is turned off, the driver leaves the car.
The driver's door closes, this should cause the engine to stop.
To subsequently start the operation of the power unit, the second key on the communicator is clicked.

Time Trigger Setting

The user can configure the option to be triggered daily, with a repeat every 24 hours. You can also configure it to start every 2, 4 or 8 hours. To activate the function, you need to complete the reservation procedure.

To complete the task you need:

Disable timer function. To do this, click the keys 2 and 4.
To activate the programming mode, buttons 1 and 2 are pressed, they must be pressed for 2 seconds.
To enter the setup menu, the fourth key is clicked 13 times. With each subsequent click, a signal will sound.
The repeat time is selected by pressing the keys. When you click on the second button, the time will be 8 hours, on the third - 4 hours, on the fourth - 2 hours.
The timer is being activated.

User Marat Askarov spoke in detail about setting the time on the Sherkhan Magikar 5 alarm communicator.

Temperature trigger setting

When this function is activated, the readings of the temperature controller installed in the passenger compartment are used. In the cold season, the values can be -15 or -25 degrees, in the warm - up to +60 degrees.

The setting is done like this:

The option to start the engine by timer is disabled.
The fourth key is clicked 21 times.
Use the keys to select the threshold for disabling the option. Button 2 to turn on the internal combustion engine at -15 degrees Celsius, button 5 - at -25 degrees, and 4 - at +60.
After selecting a value, the option is activated.

Configuring autostart according to the voltage of the on-board network

If you configure this function, then the autostart threshold will be 11.5 volts of voltage in the mains:

Key numbered 4 is clicked 20 times.
The voltage trigger is activated by the second button.
To change the operating time, the fourth key is clicked 12 times.
Time selection is made using buttons 1-4.

How do I disable autoplay?

Resetting autorun settings is performed in the same way as their purpose. To disable the option, select the corresponding function on the key fob and set its inactive status.

The Galileosky channel spoke about the implementation and disabling of the autostart option.

Possible malfunctions of the Scher-Khan Magicar 5 alarm

If the autostart stops working and the engine does not start, the reason depends on the nature of the breakdown:

The powertrain will not start, but the car owner has completed the backup procedure. With such a problem, the first reason why the options do not work may be the oxidation of contacts on safety device... The element is installed in the power supply circuit of the main module. Also, the reason may lie in the incorrect operation of the bypass device of the standard blocker. Sticking of contact elements in the control relay is possible.
The motor starts but stops after a few seconds of operation. If you start the engine with a key, it will turn on. The problem may lie in the failure of the five-contact relay, which is located in the microprocessor module.
Incorrect setting of the autorun function. To solve the problem, you need to reset all the settings of the anti-theft complex to the factory settings. Then the option values are readjusted.
The problem may lie in the activated Jack service mode. If this function is enabled, the diode element will light up without interruption. After turning off the service mode, the function will resume.

How to install an alarm?

It is necessary to mount and connect the systems as follows:

The battery is disconnected to remove voltage from the on-board network.
The microprocessor device is being installed. To do this, you need to remove the lining in the cabin and put the unit in a hidden place. During installation, the device is securely fixed to prevent the negative impact of vibrations on the module. It is recommended to place the unit under the dashboard or in the free space behind it.
The siren is being installed under the hood of the car. The place must be chosen so that there are no sources of moisture nearby or high temperatures... The siren is mounted with the horn downwards to prevent moisture accumulation inside. After installation, you need to make sure that the device and its wires will not be accessible from under the bottom of the car.
An antenna module with a diode indicator is installed. Installation of these elements is carried out on the inner surface of the windshield, it must first be cleaned and degreased. Fixation is carried out with glue or double-sided tape.
The temperature controller is being installed, as well as the shock sensor. These elements are installed in the vehicle interior. The wires for their connection are laid under the plastic sheathing.
Limit switches are installed on the doors, luggage compartment and bonnet. The wires from them must be laid so that they do not come into contact with moving parts of the body. The cables are laid under the cladding.
A service button is installed in the car interior. Its installation must be carried out in a hidden place, but the consumer must have access to the button from the driver's seat. The button can be disguised by wrapping it with black electrical tape.
At the final stage, all components are connected to the microprocessor module. The engine blocking relay is connected to the ignition switch.

Download Scher-Khan Magicar 5 installation and operating instructions in PDF format

A detailed guide on how to properly use and install the alarm can be downloaded from the link.

How much does the Scher-Khan Magicar 5 alarm cost?

The approximate cost of the anti-theft system is shown in the table.

Video "A detailed review of the anti-theft system Magikar 5"

Channel "Ramin Drive" presented a video describing the main features and functions of this anti-theft installation.

MANUAL

PURPOSE OF KEYFOB-COMMUNICATOR BUTTONS

Example of notation:

I - fast (0.5 sec.) Pressing the button

I– - long (2 sec.) Pressing of the button

(I + II) - fast (0.5 sec.) Simultaneous pressing of buttons

(I + II) - - long (2 sec.) Simultaneous pressing of buttons

Number

buttons

Time

pressing

Function (mode)

Enable security mode

Stop alarm mode

Enable starter / ignition interlock

Close the locks

Disarm security mode

Stop alarm mode

Disable starter / ignition interlock

Open the locks

Turn on / off the function "Free

Turn on / off display backlight

Checking system status

Open trunk

PANIC or JackStop ™ modes. For

to stop press button I or II

Turn on / off siren signals

Office add. channel 1

Shock sensor enable / disable

Office add. channel 2

Enable / Disable Timer Start

TURBO mode enable / disable

Entering the programming menu 1

SCHER-KHAN MAGICAR 5

1) Factory value. Two-step disarming is disabled. For
disarming, just press the button "II" of the key fob
2) Disarming confirmation is required. If using the code
PIN1 disabled (programmable function 1-6 in factory default),

it is necessary to press the button "II" of the key fob again. If used

four- or two-digit PIN1 code (programmable function 1-6

has the value II or III), it is necessary after pressing the button "II" of the key fob

sequentially press four (or two) buttons of the key fob with numbers,

the corresponding digits of the PIN1 code. Only after the right

after performing the second step, the system will be disarmed. If the code is not

entered within 15 seconds or an incorrect code is entered, the system will switch

into a state of alarm

Programmable function 1-20: "Automatic start
by battery voltage "

to perform automatic timer start.

This programmable function has two meanings:

1) Factory value. Automatic voltage start
the battery is not used
2)
the battery voltage does not drop below 11.5 V, or

the temperature condition assigned by the programmable

function 1-21

Programmable function 1-21: "Automatic start
by the threshold temperature value "

This function allows you to enable or disable the corresponding condition.

to perform an automatic timer start and select

temperature threshold.

This programmable function has four meanings:

1) Factory value. Automatic threshold trigger
temperature value is not used
2) The next timer start will be delayed until
the temperature will not drop below -15

C or battery voltage is not

Car Alarm Sherkhan 5 User Manual

MAGICAR V

User guide

PURPOSE

The Sherkhan 5 system is a car alarm with the ability to be controlled by radio channel using a key fob communicator with a liquid crystal display. The system exchanges information between the communicator keyfob and the processor unit at a distance of up to 1500 m. Sherkhan 5 has a function of automatic engine start by commands from the keyfob or by commands from the internal timer. The system is designed to operate on gasoline or diesel vehicles with a fuel injection system and a 12V on-board network. Protection of the processor unit, shock sensor, call sensor, antenna unit is made in accordance with the IP-40 standard and provides for installation in the passenger compartment. The siren is made in accordance with the IP-65 standard and can be installed in the engine compartment, away from the exhaust manifold and high-voltage systems.

Keyfob communicator functions

Multifunctional, 4-button LCD keyfob communicator
Protection against interception of code messages MAGIC CODE
Audiovisual confirmation of executed commands
Vibration bell
Loud beeps
Ultra-long-distance communication up to 1500 m with a processor unit
Automatic display backlight
Low battery indication
Vehicle battery voltage display
Temperature display in the vehicle interior
Time display
Indication of engine running time in automatic mode
Remote engine start
Programming the engine start time (accurate to the minute)
Sound and visual reminder mode of receiving alarm message
Operative, from a key fob, programming of all system functions
Economical food (one AAA cell)

Functions of the processor unit

Automatic engine start of vehicles with automatic or manual transmission
Starting system operation with both gasoline and diesel engines
The operation of the starting system with engines with a turbine
Starting the engine on command from the remote control
Automatic engine start every 2 hours
Automatic engine start at a predetermined time every 24 hours
Tracking engine start by signals from the generator or by noise in the on-board network
Personal code for access to the car interior in case of key loss
Power output for controlling the central locking of the car
Power output for unlocking the trunk lock
Alarm control power output (two circuits)
Latching relay type programming
Automatic arming (programmable function)
Sound warning before automatic arming
Automatic return to armed mode if the door has not been opened
Sound warning before automatic return to armed mode
Security mode without siren signals
Two universal programmable control channels for additional devices
Possibility to connect negative and positive door sensors
Negative trunk sensor input
Locking and unlocking doors when starting and stopping the engine
Possibility of arming with and without siren confirmation signals
Open door alarm warning (programmable function)
Panic or JackStop mode
Highly sensitive two-level shock sensor with sensitivity adjustment
"Hands free" function for automatic arming / disarming when the owner moves away / approaches the car
Dual-mode hands-free function
Side lights warning not switched off

TECHNICAL PARAMETERS Sherkhan 5

Alarm types:

Influence on the main and additional electrical equipment of the car

STSTS controls power supply to:	Maximum channel current
Starter or ignition interlock circuit	Imax = 0.2 A
Port side alarm circuit	Imax = 10 A
Starboard alarm circuit	Imax = 10 A
Ignition circuit	Current Imax = 30 A
Accessory chain	Current Imax = 30 A
Starter chain	Current Imax = 30 A
Ignition circuit 2	Current Imax = 0.2 A
Additional siren	Current Imax = 2 A
Relay for control of unlocking of electric door locks or unlocking of the standard system of the Central locking (CL) of the car	Current Imax = up to 15 A
Control relay for locking the electric door locks or locking the standard Central locking system (CL) of the car	Current Imax = up to 15 A
Trunk lock electric control relay	Current Imax = 10 A
Accessory Control Channel 1	Current Imax = 0.2 A
Accessory Control Channel 2	Current Imax = 0.2 A
Channel for disarming the STSTS standard installed on the car	Current Imax = 0.2 A

Control methods

Remote radio frequency transmitter (key fob) at a frequency of 433.92 MHz ± 0.2% at a power not exceeding 10 mW
From the ignition key
Automatically by signals from sensors

Protection of electrical circuits

Fuses. (Automotive time delay fuses according to the wiring diagram)

Spheres of protection

Other parameters

Batteries

* The table shows the average. The service life of the key fob battery depends on the intensity of use of the key fob and the quality of the battery, the operating modes of the key fob.

ATTENTION!

Use only high quality batteries. The use of a low quality battery can lead not only to a reduction in the service life of the key fob, but also to damage it.

KEY FOB COMMUNICATOR

Preparing the keyfob communicator for work

Before using the key fob, it is necessary to bring it into working condition, because during transportation and storage, an insulating gasket is installed between the contact of the battery and the contact plate of the key fob, which prevents the battery from discharging before use. Remove the keyfob before using it. To do this, open the battery compartment cover lock, press the cover and slide it out to the side opposite to the antenna. Take out the battery. Remove the insulating strip between the battery and the collector plate. Insert the battery back, observing the polarity indicated on the bottom of the battery compartment. If there is no indication of the polarity of the battery, then it is installed with the negative terminal towards the antenna. Close the battery compartment cover. The keychain is ready for use.

Symbols on the keyfob communicator display

	Timer start indicator
	TURBO mode enable indicator
	Indicator of activation of the passive arming mode
	Hands-free indicator
	Siren signal on indicator
	Shock sensor off indicator
	Vibration chime on indicator
	Indicator for turning on automatic central locking control by ignition
	Open door indicator
	Open trunk / bonnet indicator
	Shock sensor alarm indicator (optional sensor)
	Car owner call indicator
	Running engine indicator
	Ignition on indicator in security mode, indicator of non-switched off side lights
	Indicator of operation of the transmitter of the key fob-communicator
	Battery discharge indicator of the key fob-communicator
	VALET mode indicator
	Indicator for locking and unlocking locks. Arming status indicator
	Indicator of hours, car battery voltage, temperature in the passenger compartment, engine warm-up time at automatic start

Purpose of Sherkhan 5 keyfob-communicator buttons

Example of notation:

I - quick (0.5 sec.) Pressing the button
I- - long (2 sec.) Pressing the button
(I + II) - fast (0.5 sec.) Simultaneous pressing of buttons (combination of buttons)
(I + II) - - long (2 sec.) Simultaneous pressing of buttons (combination of buttons)

Control channel number	Button number	Pressing duration	Performed function (mode)
1	I	0.5 sec.	Arming / disarming Activate / deactivate call mode Stop alarm mode Switch on / off starter / ignition interlock
2	I- (1)	2 sec.	Switch on the hands-free function first operating mode (symbol does not flash)
3	I- (2)	2 sec.	Switch on the hands-free function in the second operating mode (symbol flashes)
4	I- (3)	2 sec.	Switch off the "Hands-free" function (symbol goes out)
5	(III + IV) -	2 sec.	Recording and playback of a fragment on the voice module (Option)
6	II	0.5 sec.	Additional channel 1 control
7	III	0.5 sec.	Additional channel 2 control
8	IV	0.5 sec.	Checking system status
9	II-	2 sec.	Starting and stopping the engine from the key fob
10	III-	2 sec.	Open trunk
11	IV-	2 sec.	"Panic". To stop press button I
12	(I + II)	0.5 sec.	Siren on / off
13	(I + III)	0.5 sec.	"Valet" mode enable / disable
14	(I + IV)	0.5 sec.	Automatic central lock control by ignition switch on / off
15	(II + III)	0.5 sec.	Automatic arming enable / disable
16	(II + IV)	0.5 sec.	Timer start on / off
17	(III + IV)	0.5 sec.	Turbo mode enable / disable
18	(I + III) -	2 sec.	Shock sensor enable / disable
19	(I + II) -	2 sec.	Entering the programming menu 1
20	(I + IV) -	2 sec.	Entering programming menu 2

Note: Sherkhan 5

With a long 2 sec. Pressing the I button changes the modes sequentially in the order (1)> (2)> (3)> (1)…. In mode (2) the "Hands-free -" function has a long operating range - the symbol flashes.

Setting the time on the keyfob-communicator display

Setting the current time is required before using the system or when changing the keyfob battery. Follow the steps in the table below.

Execution steps		Pressing duration	Performed function (mode)
STEP 1	(II + III) -	2 sec.
STEP 2	I	0.5 sec.	Enabling the mode of setting the current time. The current time is blinking, confirmed by the keyfob beep
STEP 3	I	0.5 sec.	Changing the clock value
STEP 3	II	0.5 sec.	Changing the value of minutes
STEP 4	(II + III) -	2 sec.

ATTENTION!

Setting the exact time is necessary condition for correct work automatic engine start by timer.

Setting the modes of the keyfob-communicator, Vibration call, owner call, temperature display standard "° F" or "° C"

To set the required operating mode of the keyfob, follow the steps in accordance with the table below.

Note: STEP 2 must be completed no later than 15 seconds. after STEP 1.

Arming [Button (I)]

Close the doors, hood, trunk. Briefly press the button I of the key fob. The system will enter the security mode, the door locks will lock, the starter (ignition) interlock will turn on until the system is disarmed.

When arming:

Enabling sensors:

Immediately after the LED starts blinking, the system begins to monitor the status of the doors, hood, trunk, call sensor of the car owner.
The shock sensor will turn on after 30 seconds. after arming.

Note:

If, when arming, you hear three signals from the keyfob, and on the display for 5 seconds. the image of an open door or trunk is flashing, this means that the door, hood / trunk is open in the car. The door, hood / trunk sensor will be immediately armed when its functionality is restored.

The bonnet area is not shown separately on the display, the bonnet sensor must be connected to the trunk sensor wire.

Disarming [Button (I)]

When the system is armed, shortly press the I keyfob button. The system will be disarmed, the door locks will be unlocked, the starter (ignition) interlock will be disabled.

When disarming:

HANDS-FREE function [Button (I) -]

ATTENTION!

The "Hands-free" mode works only when using a communicator keyfob with an LCD display; when using optional keyfobs without a display, this mode is not available.

By pressing button I of the keyfob-communicator for 2 sec. you can turn Hands-Free on or off. When the "Hands-free" function is enabled, the system automatically enters the security mode when you move away from the car with a communicator-key fob at a distance of 15-35 m *. or disarmed and unlocks the door locks when approaching. The function has two modes of operation:

In the first mode, the mark on the display does not flash and the range of the function is minimal.

In the second mode, the label on the display with the inscription "AUTO" blinks and the operating range is maximum.

The change of operating modes takes a long time 2 sec. by pressing the I button in the following order: (Function enabled, mode 1)> (Function enabled, mode 2)> (Function disabled)> (Function enabled, mode 1)….

Arming / disarming will be accompanied by a melodic signal from the keyfob-communicator.

Constant use of the "Hands-free" function is not recommended, as its use dramatically reduces the battery life of the key fob.

* Note:

The distance from the unit to the communicator keyfob, at which the system decides to arm or disarm, may vary and depends on a number of objective reasons: the relative position of the keyfob-communicator antennas and the antenna unit, the presence of metal objects near the antennas, radio interference on the air, weather etc. …

When Hands-Free is enabled:

The change of the mode is accompanied by one signal from the communicator keyfob.

When you deactivate the HANDS-FREE function:

Starting the engine on command from the remote control [Button (II) -]

To start the engine, press button II of the remote control for 2 seconds. The system will enter the security mode, the door locks will be locked, the car engine will start. After the engine has started, information on the time remaining until the engine stops operating in automatic mode will appear on the display of the key fob-communicator. The engine running time is programmable and can be 15/25/45/5 minutes (programmable function 2-4). To start driving. You need to open the door, insert the ignition key into the lock and turn it to the "ON" position. To do this, you have 20 seconds, after this time the system will transfer control to the ignition switch, if you have not turned on the ignition, the engine will be stopped.

If the launch did not happen the first time, the system will try again. The system makes no more than three startup attempts, after which it goes into standby mode. If the car engine does not start after the last attempt, contact a service station to diagnose your car.

At the time of launch:

The system will not start the engine if:

Ignition is on
The car's engine is already running
Door or hood / trunk open
The redundancy mode for vehicles with manual transmission has not been fulfilled

On successful launch:

Note: If the car's engine is started automatically, the current time indicator shows the time remaining until the engine is stopped. The time is displayed in countdown mode. Time display format in this mode: [XX min: XX sec.]

When the engine stops automatically:

Trunk opening [Button (III) -]

Press and hold for 2 sec. button III of the key fob, after which the trunk will open. If the system is armed (the doors are locked), then it will be disarmed, the doors will be unlocked, the starter lock will be disabled. To implement this function, it is necessary to have a trunk lock solenoid connected to the corresponding output of the main unit of the system.

When opening the trunk:

Checking the system status [Button (IV)]

If you need to check the system status, shortly press the IV button of the keyfob-communicator. Information about the system state will be shown on the keyfob-communicator display, as well as confirmed by siren and alarm signals.

When checking the system status:

When checking the status of the Sherkhan 5 system, the current time indicator shows the temperature in the car. Temperature can be displayed in either ° F or ° C.

The temperature inside the car is 10 ° C.

Repeated short pressing of the IV button of the keyfob-communicator within 6 seconds after the first one allows you to view information about the car battery voltage in volts.

The voltage on the car battery is 13.9V.

Panic or JackStop mode (anti-capture) [Button (IV) -]

By pressing the button IV of the key fob for 2 sec. The system will enter Panic mode or JackStop mode(anti-seizure protection) - programmable function 1-4 .. If the system was disarmed, it will be armed, the door locks will be locked. The siren will sound for 90 seconds, the alarm will flash for 90 seconds. The "Panic" mode stops the automatic engine start mode. After 90 sec. the system will enter the armed mode until it is disarmed by the key fob or by the emergency shutdown mode. The "Panic" mode can be stopped by a short press of the I button. The "Panic" and JackStop modes are used in case of danger or when it is necessary to draw attention to the car.

When the "Panic" and JackStop modes are activated:

Differences in the "Panic" and JackStop algorithms (depending on the selected value of the programmable function 1-4):

ATTENTION!

JackStop can only be used in an emergency. It is not a standard, constantly used CTCTС mode. it provides for stopping the engine while driving.

When choosing one or another mode, consult a specialist.

Silencing off the siren signal [Button (I + II)]

By briefly pressing the buttons I + II of the key fob simultaneously, you can turn on or turn off the siren signals. In this case, the key fob signals and alarm signals will work as usual. The siren activation is indicated by the presence of a symbol on the key fob display.

When the siren signals are turned on:

When the siren signals are turned off:

VALET Mode [Button (I + III)] Sher Khan 5

To disable the security functions of the system and when transferring the car to a service station for service, you can use the VALET mode. To do this, briefly press the buttons I + III of the remote control.

In the VALET mode, you can control the locking and unlocking of the door locks. To lock or unlock the locks, briefly press the I button.

The VALET mode is indicated on the display by the symbol

To exit the VALET mode, shortly press the I + III buttons of the keyfob

When VALET mode is on:

When VALET mode is turned off:

Disabling the two-level shock sensor [Button (I + III)] Sherkhan 5

You can turn off the two-level shock sensor. Press and hold for 2 seconds at the same time. buttons I + III of the keyfob, as a result the sensors will be turned on or off. The sensor disconnection is indicated by the symbol on the keyfob display. Switching off the sensor is necessary if you leave the car where false alarms are possible (the car is parked near tram tracks, a child or an animal is left in the car).

When disabling the shock sensor:

When the shock sensor is turned on:

The shock sensor is called two-level, because it has two levels of response from the impact on the car.

In case of a weak impact, the system warns with 4 short siren beeps and 4 flashes of the alarm. Key fob - the communicator beeps short, the vehicle strike symbol flashes on the display. In case of strong impact, the system goes into alarm mode for 30 seconds.

Central locking control for turning the ignition on and off [Button (I + IV)]

By briefly pressing the buttons I + IV of the key fob at the same time, you can turn on or off the automatic control of the central lock (CZ) by turning the ignition on and off. If the function is enabled, the door locks will be automatically locked after 30 seconds. after the engine is started and all doors are closed, the hood / trunk are closed. The locks are unlocked immediately when the ignition is turned off. The activation of the function is indicated by the presence of a symbol on the key fob display.

When turning on the central locking control function from ignition:

When turning off the central locking control function from the ignition:

Passive arming [Button (II + III)] Sherkhan 5

The passive arming function can be turned on / off by short-term pressing of the P + W keyfob buttons. When passive arming is on, the system automatically enters the armed mode after 30 seconds. after closing the last door or after disarming with the key fob. The system warns of passive arming with alarm and / or siren signals every 10 seconds. If within 30 sec. the doors (hood / trunk) were opened, the system will enter the armed mode after 30 seconds. after closing the doors (hood / trunk).

When passive arming is enabled:

When disabling passive arming:

Setting the timer for automatic engine start [Button (II + IV)]

Briefly press the buttons II + IV of the remote control to enable or disable the engine start by timer. The indication of the start of the engine by timer is the presence of the "TIMER" mark on the key fob display. The system provides two timer engine start modes. The first mode allows you to start the engine every day at a predetermined time, the second mode allows you to start the engine periodically, every 2 hours to warm up (or cool the cabin in countries with hot climates). The two modes cannot be used at the same time, the mode you need can be selected by programmable function 2-3.

To automatically start the engine by timer at the required time (24 hours), it is necessary to reserve this mode. For this:

Select start time (see table)
Press the II + IV buttons and turn off the "TIMER"

Execution steps	Button number or combination of buttons	Pressing duration	Performed function (mode)
STEP 1	(II + III) -	2 sec.	Entering the keyfob functions programming mode. The appearance of the symbol is confirmed by the sound signal of the key fob
STEP 2	II	0.5 sec.	Enabling the timer setting mode. The readings of the previously set time are blinking, confirmed by the keyfob sound signal
STEP	I	0.5 sec.	Changing the clock value
STEP	II	0.5 sec.	Changing the value of minutes
STEP 4	(II + III) -	2 sec.	Exit the keyfob functions programming mode. Confirmed by a sound signal from the keyfob

In order to enable or disable the engine start by timer every 2 hours, shortly press buttons II + IV of the remote control. Setting the start time in this mode is not required, the first engine start will occur 2 hours after the mode is turned on.

When starting the engine by timer:

When turning off the engine start by timer:

Note: Automatic start of the engine on a timer every 24 hours is useful for daily starting the engine at a certain time if your car is parked outside the range of the key fob.

ATTENTION!

The time for starting the engine on a timer of 24 hours can be shifted up to ± 2 minutes per day.

TURBO mode [Button (II + IV)]

If the car has a Turbo engine, then it is not recommended to stop it immediately after long-term operation at high speeds. The engine must idle for a while to cool the turbine. For this, the SCHER-KHAN MAGICAR V system provides a TURBO mode (turbo timer). If the TURBO mode is on, then at the end of the trip the engine will run for 2 minutes. To enable or disable the TURBO mode, shortly press the buttons III + IV of the remote control.

When TURBO mode is on:

When TURBO mode is turned off:

To activate the mode at the end of the trip, do the following:

Place the transmission lever in neutral or P.
Turn the key in the ignition switch from ON to OFF. The engine will continue to run after that for another 2 minutes.
Get out of the car, close the doors. As soon as the doors are closed, the alarm will flash

Now you can arm the system. In this case, the engine will run until 2 minutes have elapsed. interval. When the car is armed, the door, hood / trunk sensors, driver call sensor are armed immediately, and the shock sensor will start working after the engine stops. The engine will be stopped immediately when the door, hood / trunk sensor is triggered and the system will go into alarm. If necessary, you can urgently stop the engine by pressing for 2 sec. button II of the keyfob.

Additional Channel 1 Control [(II) Button]

If your car is equipped with an electromechanical hood lock, an additional pre-heater or other service equipment, You can control the operation of these devices using the key fob. To do this, shortly press button II of the remote control. A short or long signal will appear at the output of additional channel 1 of the processor unit (programmable function 2-5). The siren and side light signals will differ when an additional channel is controlled, depending on the state of programmable function 2-5. If the channel is programmed for a long signal (Value 4 of the programmable function 2-5), the system will confirm its activation and deactivation by siren and alarm signals. If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel. The additional channel does not work in VALET mode and in alarm mode.

Enabling an additional channel:

Note: If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel (programmable function 2-5)

Control of additional channel 2 [Button (III)]

If your car has an electromechanical hood lock, an additional pre-heater or other service equipment, you can control the operation of these devices using a key fob. To do this, shortly press button III of the remote control. A short or long signal will appear at the output of additional channel 2 of the processor unit (programmable function 2-6). The signals of the siren and side lights will differ when controlling an additional channel, depending on the state of programmable function 2-6. If the channel is programmed for a long signal (Value 4 of the programmable function 2-6), the system will confirm its activation and deactivation by siren and alarm signals. If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel. The additional channel does not work in VALET mode and in alarm mode.

Enabling additional channel: Sherkhan 5

Switching off an additional channel:

Note: If a short signal is programmed at the output of the additional channel, the system will only confirm the activation of the channel (programmable function 2-6)

Alarm mode

If the door, hood / trunk is opened in the armed mode, the system will go into alarm mode for 30 seconds, alarm signals and sirens will last for 30 seconds. At the end of 30 sec. the system will return to armed mode. If the shock sensor alarm zone is triggered (strong impact), the system will go into alarm mode for 15 seconds, alarm signals and sirens will last for 15 seconds. At the end of 15 sec. the system will return to armed mode. When the shock sensor warning zone is triggered (weak impact), the system will not go into alarm mode, but will only issue a series of four short signals with a siren and an alarm. You can end the alarm mode by short pressing the I keyfob button. In this case, the locks will not be unlocked, and the system will switch from alarm mode to armed mode.

In alarm mode:

Reminder mode

If the communicator key fob received an alarm signal from the door, hood / trunk sensors, shock sensor, call sensor and you did not notice this immediately, the key fob, after the alarm signal is transmitted, goes into the reminder mode (with short beeps and indication of the zone that caused the alarm mode) ... To terminate the reminder mode and check the vehicle status, briefly press button IV of the key fob or button I to exit the security mode and unlock the doors.

In reminder mode:

Note: The communicator keyfob does not go into reminder mode when it receives a warning signal from the shock sensor (weak impact)

Car owner call

If you need to call the car owner, knock with a hard object (coin, keys, etc.) near the call sensor. The call sensor LED will flash green. The function of calling the car owner is available immediately after arming. To stop the signals from the keyfob-communicator, press the button I of the keyfob. To stop the signals of the keyfob-communicator and check the condition of the car, shortly press the IV button.

When calling the car owner:

Access to the car without key fob Sher Khan 5

Access to the car without a key fob may be required in a number of cases. For example, if the key fob is lost, if the battery in the key fob has run out, if you are relaxing on the beach and do not want to take the key fob with you (the key fob and keys are locked in the car). The SCHER-KHAN MAGICAR V system provides this opportunity. To allow access only to you, the system uses a personal code consisting of four digits. The value of each digit of the code can vary from 1 to 9. Thus, the code can have a value from 1111 to 9999. The code is entered and recorded through the call sensor of the car owner.

Personal code entry:

In order for you to use this function, you must enter your code into the system memory. To do this, follow several steps:

Turn on the ignition
open the door
While the LED is blinking, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the selected digit with red flashes and will start flashing again.
While the LED is blinking, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the selected digit with red flashes and will start flashing again.
While the LED is blinking, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the selected digit with red flashes and will start flashing again.
While the LED is blinking, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. the LED will confirm the selected digit with red flashes.
To confirm the programming of the code, you will hear one siren signal, the alarm will flash once.

If at any of the steps you made a mistake, then you need to record the code, starting from point 1.

Personal code entry:

Tap the call sensor 10 times. Each time the LED in the sensor will flash green. The time between blows must be less than 1.5 seconds.
The LED will quickly flash red to confirm that the previous step has been completed. If the LED does not flash red, then start from step 1 again.
While the LED is blinking, tap the call sensor the number of times corresponding to the first digit of the code. After 1.5 sec. the LED will confirm the entry of the first digit with red flashes and will start blinking again.
While the LED is blinking, tap the call sensor the number of times corresponding to the second digit of the code. After 1.5 sec. the LED will confirm the entry of the second digit with red flashes and will start blinking again.
While the LED is blinking, tap the call sensor the number of times corresponding to the third digit of the code. After 1.5 sec. the LED will confirm the entry of the third digit with red flashes and will start blinking again.
While the LED is blinking, tap the call sensor the number of times corresponding to the fourth digit of the code. After 1.5 sec. the LED will confirm the entry of the fourth digit with red flashes.
If the code is entered correctly, the system will be disarmed, the door locks will open, and a signal will be sent to the communicator to disarm the system. If the code is entered incorrectly, then the owner's call signal will be sent to the key fob, and it will be necessary to repeat all actions starting from point 1.

The system allows five attempts to enter the code within 30 minutes. If the code was entered incorrectly, then its entry is blocked for 24 hours or until you disarm the system using the keyfob.

Battery protection (warning about unplugged dimensions)

The system helps to protect the vehicle battery from discharge. If you forgot to turn off the side lights, then when arming, the communicator keyfob will give a series of beeps for 5 seconds. At this time, the images of the lock and side lights will flash on the display. The warning beep will repeat every 30 seconds. three times.

Starter or ignition interlock

The system in the security mode will not allow starting the car engine. When an attempt is made to start the engine in the armed mode, the system will send an alarm signal to the communicator key fob. The ignition switch-on alarm will be indicated by the flashing of the side lights on the communicator key fob, sound and vibration signals. The engine blocking mode is selected when the system is installed at a service station and depends on the values of two programmable functions 1-4 and 1-8. You can find out more about blocking the engine of your car at the place of installation of the system. When starter lock is selected, the system will prevent the car's starter from restarting if the engine is started in automatic mode.

Open door warning

The system warns of an open door (programmable function 1-2). When a custom function value is selected, the alarm flashes if the car door is open.

Protection of the radio channel from interception of the code

The system has special protection for the commands transmitted by the key fob. Each time you press the button on the system key fob, the code message changes according to a special algorithm. This is done to protect the system from interception of the code and its selection (intellectual hacking of the security system). The code protection algorithm is specially developed for the SCHER-KHAN MAGICAR system and is unique, not used in one security system of other brands.

Motor protection in auto start mode

The system continuously monitors engine operation in automatic start mode. If the engine stops before the end of the warm-up cycle (engine malfunction or out of fuel), then no later than 20 seconds. the system processor unit will turn off the ignition. Automatic restart of the engine will not be possible until the malfunction is eliminated. For vehicles with a manual transmission, it is necessary to execute the redundancy mode again.

Shock sensor sensitivity adjustment

You can adjust the sensitivity of the shock sensor depending on your requirements. A regulator is provided on the sensor to adjust the sensitivity. Turning the knob clockwise increases the sensitivity, and counterclockwise decreases it, until the sensor is turned off. Consult a service station for the location of the shock sensor, it should be easily accessible for adjustment.

Adjusting the sensitivity of the owner call sensor

You can adjust the sensitivity of the car owner call sensor depending on your requirements. To adjust the sensitivity, a step regulator with three positions is provided on the sensor. The extreme left position of the regulator corresponds to the minimum sensitivity of the sensor, the extreme right - to the maximum. The sensor should be located in the lower corner of the car's windshield.

Adjusting the volume of the siren confirmation signals

You can adjust the volume of the siren short beeps. To decrease the volume, you must cut the loop from the wire on the siren body. The system can be equipped with any siren in accordance with the wishes of the owner, including one where there is no adjustment option.

Redundancy Mode (Manual Transmission Only)

The standby mode prevents the engine from starting automatically if the manual transmission lever is not in neutral. Depending on your requirements, you can choose one of three backup algorithms (programmable function 1-6).

Algorithm 1

Algorithm 2

To perform redundancy (preparing the car for the subsequent automatic engine start), do the following:

At the end of the trip, without turning off the engine, set the gear lever to neutral.
Close the hood / trunk doors
Remove the key from the ignition switch (OFF position). The engine will continue to run
Open the door and exit the car. Close the door. The engine will stall.

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnostics of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no redundancy mode and automatic engine start will not occur. In this algorithm, redundancy will be disabled if the door, hood / trunk is open at the time the ignition is turned off.

Algorithm 3

To perform redundancy (preparing the car for the subsequent automatic engine start), do the following:

At the end of the trip, without turning off the engine, set the gear lever to neutral.
Close the hood / trunk doors
Press for 2 sec. button II of the keyfob
Remove the key from the ignition switch (OFF position). The engine will continue to run
Open the door and exit the car. Close the door. The engine will stall

Opening the door after completing the fifth step will make it impossible to automatically start the engine. Diagnostics of the reasons for its failure is described below.

If at least one step from the above algorithm is not performed, then there will be no redundancy mode and automatic engine start will not occur. In this algorithm, making a reservation requires you to press button II of the key fob each time before turning off the ignition (by turning the key in the ignition lock to the OFF position).

ATTENTION!

Close the sunroof and windows before exiting the vehicle. Do not leave people or animals in the vehicle while performing the redundant mode.

Do not automatically start the engine while people or animals are in the vehicle.

Leave the transmission lever in neutral at all times. Do not use automatic engine start on open top vehicles.

If the operation of the backup mode differs from the described algorithms or does not occur, immediately contact your service station for advice. Do not use the automatic engine start until the cause of the malfunction is eliminated.

PROGRAMMING NEW KEY FOBS

The system can memorize the codes of three key fobs. Follow two steps to program new keyfobs.

Turn the key in the ignition switch from OFF to ON three times. The alarm will flash once to confirm entering the programming mode.
Not later than 4 sec. after the flashing of the alarm, press the button I of the key fob, the code of which must be entered into the memory of the processor unit.

To exit programming mode, do not take any action for 4 seconds. after writing the code of the last keyfob.

If after step 1 no action is taken, after 4 sec. the alarm will flash 2 times, the system will switch from the keyfob programming mode to the VALET mode.

Note:

The system has three memory cells for storing keyfob codes. If you try to write the fourth keyfob, the code of the first recorded keyfob will be deleted.

FUNCTION PROGRAMMING WITH KEY FOB

Programming the STTS functions using a key fob consists of four steps.

Enter the programming mode and select the programming menu. To enter Menu # 1, simultaneously press buttons I + II for 2 sec. To enter Menu No. 2, simultaneously press the I + IV buttons for 2 sec. The siren will sound one short beep, the alarm will flash once, thereby confirming the successful completion of STEP 1.
Press the IV button to select the Menu function you want to change. The number of clicks must correspond to the number of the selected function. For example, to select function 4, shortly press the IV keyfob button four times. Each pressing of the button will be confirmed by a short siren sound (if enabled) and an alarm flash.
Please wait a few seconds. The system will confirm the number of the function selected to change with short siren beeps and alarm flashes. The number of beeps will correspond to the number of the selected function.
Note:

If, when choosing the function, you made a mistake with the number of clicks and (or) there are no siren and alarm signals, then you must repeat all actions, starting from STEP 1.
Press the I button to select the factory setting for the function. In confirmation of this, the siren will give one short signal, the alarm will flash once. Press the II, III, or IV button to select the optional function values. In confirmation of this, the siren will sound two, three or four short beeps, the alarm will flash two, three or four times.

Note:

If you hear one long siren signal, it means the system exits the function programming mode. To continue programming, it is necessary to repeat all actions, starting from STEP 1.

ATTENTION!

If it is necessary to change more than one function from the Menu selected by you, then the selection of each function to change must be started from STEP 1.

Programmable function menu

Menu # 1 [Button (I + II) -]

P / p No.	Function	[Button (I)] Factory default	[Button (II)]	[Button (III)]
1-1	Delay before starter rotation after ignition on. Should be increased for a diesel vehicle.	4 sec.	10 sec.
1-2	Open door warning	Not	There is
1-3	Pulse duration of central lock control. Should be increased for pneumatic central locking system	0.8 sec.	4 sec.
1-4	Panic or JackStop mode (anti-robbery)	"Panic" (Starter lock)	JackStop (Ignition lock)
1-5	Central lock control for ignition on and off	Turned off	Turned off
1-6	A method of starting redundancy. (Only for manual transmission)	Automatically whenever the ignition is turned off	Automatically whenever the ignition is turned off, provided the doors are closed	Only manual mode, before turning off the ignition to back up, press button II for 2 seconds.
1-7	Starter rotation time	Standard	Standard + Minimum	Standard + Maximum

Feature note 1-4: This function allows you to select the "Panic" mode or the JackStop mode (anti-robbery):

Setting all programmable functions of menu # 1 to factory defaults

Entering the programming mode. Press buttons I + II at the same time for 2 sec. The siren will sound one short beep, the alarm will flash once, thereby confirming the successful completion of STEP 1
Three times shortly press button III of the remote control. Each press will be confirmed by a short siren sound and an alarm flash. After some time, three siren signals will sound, the alarm will flash three times, confirming the factory settings of all programmable functions of menu no.

Menu # 2 [Button (I + IV) -]

Setting all programmable functions of menu No. 2 to factory defaults Sherkhan 5

There are two steps to complete the factory defaults for programmable functions.

Entering the programming mode. Press the I + IV buttons simultaneously for 2 sec. The siren will sound one short beep, the alarm will flash once, thereby confirming the successful completion of STEP 1
Three times shortly press button III of the remote control. Each press will be confirmed by a short siren sound and an alarm flash. After some time, three siren beeps will sound, the alarm will flash three times, confirming the factory settings of all programmable functions of menu # 2.

Scher-khan magicar V is one of the past generations of the popular alarm system that combines security, control and increase performance characteristics car function. Scher-Khan Magicar V - one of those types of car alarms that have feedback, carried out using a control key fob.

The Scher-Khan Magicar V alarm system is controlled remotely using a key fob with a display located on it. The control key fob allows you to remotely control the alarm functions using several keys on the key fob (I, II, III, IV), various combinations of buttons and pressing lengths - short presses (0.5 sec) and long (2 sec).

Setting the time on the key fob

Setting the exact time on the key fob display is a necessary procedure in order to be able to start the car engine by timer in automatic mode. Since the exact time is reset when the power is turned off, the installation is carried out not only before starting operation, but also when replacing the battery.

Setting the exact time on the key fob consists of several stages.

It is required to press a combination of buttons II and III. Pressing duration - 2 seconds. After that, the programming mode is entered, about which the owner is notified by the sound signal of the key fob, the flashing of the alarm and a special symbol on the display.
Then press the I button and hold it for 0.5 sec. Thus, the mode of setting the exact time is activated, which is confirmed by a sound signal. The device displays the current time flashing.
Then the exact time is set. With button I you can change the hour display, with button II the minute display. To change one step, hold down the desired key for 0.5 seconds.
The last stage is the exit from the programming mode, which is carried out by pressing the combination of keys II and III. Exit from the mode is confirmed by a sound signal.

Factory reset

Errors in self-programming of alarm functions may require a rollback to the factory settings. Resetting the programmable alarm functions to their factory defaults is carried out in 2 steps.

At the first stage, enter the programming mode - press buttons II and III simultaneously and hold them for 2 seconds.
In the second step, you need to press button III on the key fob three times (0.5 seconds each). Each press is accompanied by flashing "emergency gang" and a sound signal. After a short period of time, 3 signals should sound, and the alarm will flash three times. Thus, the owner is notified about resetting the programming of functions to the default settings.

Engine starting

The Scher-Khan Magicar V alarm allows you to start the car engine using the control key fob. To do this, press button II of the keyfob and hold it for 2 seconds (long press). In this mode, the alarm goes into security mode, the car doors are locked, and the engine starts. The running time of the motor can be programmed for different time periods:

5 minutes;
15 minutes;
25 minutes;
45 minutes.

Starting the engine is accompanied by several indicators of confirmation of the successful execution of the request:

siren sound
a sound signal of the key fob ;;
flashing emergency gang;
5x headlights on the key fob display

If the engine start fails, the system will retry a maximum of 2 more times. If after them the engine cannot be started, then the alarm goes into normal mode.

In order to start moving the car, the driver with the engine running from the key fob must open the doors, insert the ignition key and turn it to the ON position. To do this, the driver has 20 seconds after opening the doors. If during this period the key is not turned to the desired position, the system will automatically turn off the engine.

The alarm may not start the engine for several reasons:

the engine is already running;
the ignition is already on;
the doors or trunk are open;
the redundancy mode for vehicles with manual transmission has not been fulfilled (the control lever is not transferred to the neutral position).

Therefore, in order to automatically start the engine, the driver of a car with a manual transmission must first after stopping:

set the gearbox lever to the "Neutral" position without shutting down the engine;
close the hood and trunk;
press button II on the key fob;
turn the ignition key to the off position and pull it out (the engine will continue to run);
go out and slam the door (the engine will stall).

Autostart programming

Scher-Khan Magicar V alarm allows automatic engine start in various modes:

every 2 hours;
every 24 hours.

Starting the engine every 24 hours allows you to start the engine at the same time every day, which is convenient, for example, for warming up in the morning. Starting every 2 hours allows you to maintain the temperature of the engine and the interior on cold days or, conversely, to cool the interior during the summer season. Both timer modes cannot be used at the same time. The autorun mode is selected through the programmable functions menu.

To program autostart every 2 hours, shortly press buttons II and IV. In this case, the engine will automatically start 2 hours after pressing. Setting the time is not required in this case.

To automatically start the engine every 24 hours, you must first set the exact time on the key fob, if it is not set. (how to do it - see above). The automatic start of the motor is set as follows:

it is required to press buttons II and IV and turn off the Timer mark;
select the start time using the I and II keys;
press keys II and IV again and turn off the Timer label.

When the engine starts automatically, the key fob display shows a countdown until the moment when the engine is turned off.

Autostart by temperature

Automatic start can be set when a certain air temperature is reached, which is determined by temperature sensors installed in the vehicle interior. Temperature autostart can only be used in conjunction with timer autostart. To set autorun only when a certain temperature is reached, you must:

select autostart by timer;
switch on temperature control - press the IV button 21 times;
choose the required temperature regime(key II - –15 ° C, key III - –25 ° C, key IV - +60 ° C);
enable timer autostart mode (see above).

How to register a keychain?

The Scher-Khan Magicar V alarm can "memorize" 3 different key fobs. To synchronize a new key fob with the alarm, you must:

turn the ignition key three times from the OFF position to the ON position - the "emergency light" should flash 1 time, confirming the entry into the programming mode;
no later than 4 seconds after the flash, you need to press the I key on the new key fob;
then you need to enter the key fob code into the memory of the alarm processor unit.

The memory of the processor unit can store the data of only 3 key fobs, so when the fourth key fob is written, the code of the first is deleted from the memory.

You can exit the programming mode without taking any action within 4 seconds after the last digit of the code has been written.

How do I turn off the alarm?

To disable the security functions of the alarm system, a special VALET mode is provided. The deactivation function is necessary, for example, when transferring the vehicle to a station. service to prevent the alarm from being triggered. To switch to the VALET mode, a short press of the I and III keys is enough. You can also turn on the mode with the ignition key - just like when registering a new key fob, you need to turn the key in the cell from the OFF position to the ON position three times, that is, enter the programming mode. In the future, you should not take any action for 4 seconds, after which the system will automatically switch to VALET mode.

In the VALET mode, the door opening / closing function is retained, for which you need to shortly press the I button. You can exit the VALET mode by pressing the combination of keys I and III.

Shock sensor adjustment

The shock sensor notifies the owner of the car about an accident with the car while the car is parked with the alarm on.

Scher-Khan Magicar V alarm sensors are two-level: in case of weak impact, a 4-time sound signal is given and an alarm signal is flashed 4 times. In case of a strong blow, the key fob goes into alarm mode, which lasts 30 seconds - 30 flashes of "emergency" and 30 short beeps. The shock sensors can be turned on or off by pressing the combination of buttons I and III and holding them for 2 seconds.

Adjusting the shock sensor helps to avoid false alarms of the crash alert sensor, because with a sensitive sensor, even the passage of a neighboring vehicle can be falsely perceived by the system as an emergency shock. To adjust the sensitivity of the sensors, physical access to them is required; you can find out about the location of the shock sensors at the service station. The sensors themselves are equipped with regulators, turning clockwise increases the sensitivity, counterclockwise - reduces until the sensor is completely turned off.