What do stretch ceiling wallpapers do first. What they do first: stretch ceiling or wallpaper

Stretch ceiling: first wallpaper or ceiling, will the canvas be damaged during wallpapering or is it better to do the opposite and decorate the walls first? Many who decide to make repairs with their own hands are faced with the problem of choosing what to do first. In general, professionals allow both options, but in a particular situation, you should carefully weigh the pros and cons and start repairs. Read more about what is better to do first in this article.

If you start gluing wallpaper before stretching the ceiling and vice versa, then some of this may worsen the result of the finish in general. Therefore, it is important to know what to do first: decorate the wallpaper or install stretch ceiling.

If you do something wrong and in the wrong order, you can disrupt the entire repair. Particular attention should be paid to work if you plan to use expensive finishing materials.

How to stick wallpaper with a stretch ceiling

Before gluing materials to the surface, the walls must be leveled with plaster.

However, if there are already stretch ceilings, then there is no way to align the walls:

It is impossible for the plaster to fall on the film of the stretch ceiling.
It is impossible to plaster the walls to the end, there is a high probability of touching the ceiling with plaster, which will ruin the coating.

Answering the question: “what to glue first: ceiling or wallpaper?” - Wallpaper forward. In this case, the wallpaper is applied only after the preparation of the walls. It is impossible to level the walls after fixing the ceiling with drywall, because the profile for installing drywall sheets must be framed with another profile, which cannot be done with a soft stretch ceiling film.

To fix the ceiling baguette, a leveled surface of the walls is also required; wallpapering has not yet been completed. You need to stretch the ceiling after the wallpaper, and in order not to stain the baguette with a primer, you need to stick masking tape on it.

Depending on the type of wallpaper, the wallpaper is either glued dry on a wall smeared with glue, or also smeared with an adhesive composition. When glue is applied to the wall, it also gets on the ceiling, which is unacceptable. For this, adhesive tape is also glued. Excess wallpaper must be carefully cut with a knife.

What first: stretch ceiling or wallpaper

Certainly, correct first It's a matter of sticking wallpaper, and then installing the ceiling. Otherwise, the stretch ceiling will be crooked, it will be problematic to glue the wallpaper, the overall picture will be spoiled. However, sometimes it happens that the ceiling has already been selected, and a construction of drywall sheets. In this case, the ceiling must be carefully closed with adhesive tape and the wallpaper fixed.

How to glue wallpaper with a stretch ceiling correctly

A few points should be highlighted related to the installation of wallpaper and stretch ceiling.

Namely:

The baguette for the ceiling is always fixed first; during this, a perforator is used. Bricks during drilling leave a large amount of red dust, so wallpaper can be glued to the brick only after the ceiling has been glued.
Next, PVC is heated for stretch fabrics to 100 degrees. You can also choose any other fabrics. If you glue the wallpaper, and then install the ceiling, then the wallpaper may be damaged after heating the room. It is better to choose a fabric ceiling, it reduces the chances of damage to walls with wallpaper.
Stretch fabric it is necessary to fix it in a baguette with a spatula, you can also install a fillet, it hides the gaps between the walls and the baguette. But it can not be pasted in front of the wallpaper, otherwise the coating will be uneven and ugly.
In order not to spoil the finished ceilings during wallpapering and not to stain them while priming the surface, you must first fix the baguette, and then glue the wallpaper to the profile level, fix the stretch fabric. Then the walls and wallpaper will be clean.
When working with expensive wallpaper (for example, textile), it is necessary to save material. In this case, the customer himself decides what should be done first: apply wallpaper to the walls or install a stretch ceiling. It must be remembered that the ceiling in any case will last several years longer than even the most expensive wallpaper.

The main difficulties in the repair process are the fear of spoiling either the wallpaper or the ceiling. It is best to consult with professionals in order to make the right decision on what to install first.

First of all, you need to prime and level the walls, otherwise the baguette will twist, and the ceiling will be stretched crookedly. If the ceiling is already stretched, then it must be carefully protected, and the walls should be pasted over with wallpaper carefully, touching the canvas as little as possible.

Let's approach the issue from the other side and give arguments in favor of the initial installation of the ceiling, and then - wallpapering:

Even if a gas gun is used to heat the structure, it is not directed to the walls, and the professional will carefully monitor the safety of the coating.
When drilling holes to fix the baguette, a lot of dust is generated, which can ruin the wall decoration. However, the wallpaper can be vacuumed, and some types of wallpaper can even be washed.
Often, even the ceiling manufacturers themselves say that baguettes should only be installed on a fully designed and leveled wall surface.
Do not be afraid to paint the walls and wallpaper after installing the suspended structure, masking tape will help not to touch the ceiling. Also, the distance between ceilings and walls can be re-glued using ceiling plinth.

We can summarize and say that the masters are not afraid to finish the wallpaper after the ceilings, but you should think several times before doing this and carefully protect the false ceiling.

How to stick wallpaper under a stretch ceiling yourself

When sticking wallpaper with your own hands, you must use masking tape in the venues finishing works. If glue still dripped onto the ceiling, you need to wipe it with a damp cloth as soon as possible.

If you plan to paint the walls, then it is better to stretch the ceilings after painting, but it is better to install a baguette for it immediately after leveling the walls.

When stretching the canvas, glue the wallpaper as carefully as possible, without touching the canvas with a knife when cutting the wallpaper. Be sure to protect the ceiling with masking tape, and after working with wallpaper, carefully remove it.

Secrets of wallpaper stickers near the stretch ceiling (video)

In conclusion, it should be said that everyone must decide for himself what to do first. Often repairs are carried out with already installed ceilings, then it is necessary to handle the stretch fabric as carefully as possible and use masking tape. It should be remembered that the baguette is mounted on a prepared, even and puttied wall. In any case, the work requires the utmost accuracy and concentration, then the ceilings and wallpapers will delight you for a long time.

Repair is the word that scares almost everyone. Of course, I want to change the situation and update the interior, but the process itself does not deliver pleasure. High costs, a huge scale of work and the nuances that arise in the process can lead even the most calm person. Often, questions arise, but where is it better to start, from the walls or the ceiling? What do they do first: glue wallpaper or install a stretch ceiling? Let's try to understand this issue further.

Work can be carried out in any order if they are performed by highly qualified specialists. But if repairs are done by people who do not have enough skills, then unpleasant nuances may arise. Before proceeding to the main stage, you must complete preparatory work. They include:

Cleaning walls and ceilings from old finishing materials.
Coating surfaces with antifungal agents.
Minor defects and cracks are eliminated.
Walls and ceilings are plastered and plastered.

After that, all necessary measurements and calculations are carried out, materials are purchased in the right amount. The final stage is the fastening of the baguette at the base of the structure.

What comes first: pasting the walls or installing a stretch fabric is influenced by the design of the top that you have chosen. There are several types of ceilings that are popular now. This:

The stretch fabric will not be placed around the entire perimeter of the room, but a box will be inserted. This design involves the preliminary installation of drywall oval, round, square or any other shape. The surface is puttied, painted, and only after that the tension fabric is installed. From the foregoing, it follows that the room should be as ready as possible, all finishing work has been completed before installing the ceiling.
The stretch fabric is decorated with baguettes. With this option, a strict order of work is recommended. First, the walls are puttyed, then the tension coating is installed. Lastly, a baguette is attached. It is puttied at the joints and painted. Only after all the described procedures, the walls are finished.
The stretch fabric covers the perimeter of the top completely. Here you can choose any sequence. It all depends on how it will be easier for you, and how much you can cope with the nuances that will arise in the process.

The rough work is over and the fun begins. Consider both options and possible consequences their applications.

First, wallpapering.

This option is chosen by many, believing that the glue, paint or solvent that is used in the pasting process will greatly pollute the ceiling. Some compounds are capable of causing irreparable damage to the canvas, ruining it appearance or invoice. This is especially true for paints, if you are gluing wallpaper, which you will then process with them.

Disadvantages of the chosen method and options for their solution:

When installing a baguette, a lot of holes are drilled. This often leads to soiling of the wallpaper. To prevent this, you can use a hammer drill with a vacuum cleaner. It will not protect against all dust, but will reduce its amount to a minimum.
Installation of a stretch ceiling takes place at a high temperature. The room heats up to 60 degrees above zero. Such conditions can cause the wallpaper to come off. But this situation arises due to a violation of technology. Install the canvas only after the wallpaper is completely dry. This takes about 6 days at room temperature, so take your time. Having finished gluing, invite measurers to order a stretch ceiling. As a rule, it is produced within a week. This time is just enough for the wallpaper to dry.
Careless use of tools such as a spatula, scissors, can damage the ceiling. Here, when cutting canvases, jewelry accuracy is required.
Re-replacing the wallpaper, after the repair is completed, will be much more difficult to do.

First the ceiling, then the wallpaper.

Stretch ceiling can be installed in two ways:

Harpoon method. To begin with, the parameters of the room are measured, for the manufacture of the canvas. After, experts install a baguette, on nails driven into the wall in advance. This method will remove up to 4 centimeters in height. With the help of a special gun, the fabric is heated, stretched and snapped into place. After some time, it hardens and looks perfectly even.
The second way is without a harpoon. The canvas is clamped, like fabric on a hoop. This is a cheaper method that does not require preliminary measurements. But, in case of poor-quality installation, the ceiling may sag.

In addition to film, there are fabric ceilings. Their feature is that they do not warm up during installation. There are no seams on them, which makes such a stretch fabric quite durable. Installation of a fabric ceiling does not begin from the corners, but from the middle. It turns out something like a cross. Already guided by it, the material is pulled from the central part, to the corners. Installation is carried out with a special spatula. The edges that hang down are trimmed with a knife.

Important! If wrinkles occur during the installation of the fabric web, do not panic. They are easy to fix with a building hair dryer.

When the stretch ceiling installation method is chosen, consider the arguments of experts in favor of what wallpaper should be glued after. The main one is that it is possible to cover the canvases with a film so as not to get dirty. Otherwise, the ceiling cannot be protected in any way. Also, the heat treatment of PVC coatings will not affect the wallpaper in any way.

In addition to polluting the ceiling with coloring and adhesive materials, the disadvantages include trimming the wallpaper. After gluing the technological tape, it will be quite difficult to align the canvas.

Installation of the ceiling in stages, as an option for a costly compromise

This method is rarely used by professional builders and people who make repairs on their own. It's all about what it requires more money and time to work. But if you are interested in a quality result, then you should pay attention to it.

The installation scheme takes place in several stages:

walls are aligned;
a baguette is installed;
wallpaper is pasted;
ceiling sheet is installed.

How to stick wallpaper with a stretch ceiling

The service life of stretch ceilings, as a rule, is not less than 10 years. But at the same time, you will want to change the wallpaper much earlier, after 4-5, for sure. What to do in this case, because changing everything will be quite expensive? Can be wallpapered without damaging ceiling covering. This work is carried out in several stages:

First, remove the interfering furniture and glue masking tape on the edge of the ceiling. Of course, this will not help from damage by cutting objects, but it will save you from being touched by a brush.
We clean the walls from old wallpaper. To do this, we cut them as close as possible to the base of the profile. Pick up the sharpest possible tool to make a straight line.
Wallpaper is wetted with warm water to make it easier to remove. If there are minor defects and irregularities on the walls, then they must be eliminated. But it is not recommended to level with drywall and putty when there is already a stretch ceiling.
Prepare the walls for gluing by treating them with a primer. Near the ceiling, this must be done as carefully as possible, because it will be difficult to remove pollution.
Before sticking wallpaper, it is worth deciding whether there will be a baguette in the room. Experts advise to use it. This decorative element serves not only as a decoration for repairs, but also covers uneven sections of wallpaper and the joint of the ceiling with them.
Cutting the canvases and fitting the pattern should be done on the floor. After all, leaving this matter for later, you risk damaging the stretch ceiling with sharp objects.

Wallpapering when there is a stretch ceiling is quite painstaking work. By following the simple recommendations of experts, you can do the job efficiently.

How to combine stretch fabrics and wall decor

If there is already a decision on what to do in the first place: install a stretch ceiling or glue wallpaper, but the materials have not yet been purchased, you should think about how to choose them correctly.

If you have ordinary apartment or a house with a standard wall height, you need to choose the right color scheme. It should not make the room visually smaller.
Windows that face north do not allow maximum illumination of the room. Even during the day it looks dull and gloomy. Bright colors such as orange will make the room brighter and sunnier.
The opposite situation is when the windows face south. Too bright environment will interfere. All the time there will be a desire to lower the blinds. In this case, you should choose calm colors, such as aqua, turquoise and pastel shades.
To make the room higher, you can pick up a stretch coating of a light shade. In this case, the bottom should be dark. This combination will work in contrast.
If there are no windows in the room, you should choose light shades for the top. When your taste only tells you dark colors, then buy a stretch fabric with a glossy effect. The walls will be reflected in it like a mirror. This will visually stretch the room.

Secrets of wallpaper stickers near the stretch ceiling video

You can peep the secrets of wallpaper stickers and stretch ceiling installation on the Internet. There are many videos where experts give their recommendations for the implementation repair work. We bring to your attention one of them:

When it comes to the option: “What do they do first: a stretch base or wallpaper?”, You need to know the answer in advance. It depends on the future interior design, individual preferences, the choice of a finishing company. You are initially required to draw up a detailed plan that determines the procedure for designing a separate room.

Characteristics of materials

Let's start with the main one. A stretch ceiling is a suspended structure, the material of which is polyvinyl chloride (PVC) or fabric. They are fixed on profiles made of steel, aluminum, plastic. Often the base is combined with drywall to create tiers. The fabric with vinyl is also of different levels. The strip is attached to the roof, but it is possible to the wall. It all depends on the design of the room.

Wallpaper - paper rolled canvas. Production standard: length - 10 m, width - 53 or 106 cm, depending on the material. Distinguish one- and two-layer performance, vinyl, acrylic, interlining. What composition - such a cost. The better it is, the more it will cost. Paper strips are smeared with glue when non-woven is used - glue is applied to the side fences.

Factors in Choosing a Sequence

When the repair is started, the team arrives, offering two options: first install the tension base, then paste over the sides or decorate the side rails by completing the finishing operations, and then stretch the canvas. What is more correct?

Both variations are substantiated. Focus on choosing professionals. Difficulties will arise during work, which professionals can solve. Difficulties are caused by such moments:

Is a ceiling plinth installed?
Wall material (brick, concrete).
How well the tension tape is used, the fastening technology.
High-quality carrying out of draft procedures.

Good to know! It is advisable when rough processing of the ceiling and walls is combined. Then comes the finishing touch.

Preparatory procedures for all options

First they clean up the room. They clean the old coating from paint, lime, remove stains of grease, dirt. It is impossible to leave past shortcomings: the previous finish will begin to crumble, fall in pieces on the tension structure. First, prepare the side rails before installing the material:

Remove the previous processing material (paint, plaster, tapestries).
Treated with primers against fungi.
Eliminate cracks, minor defects.
Plaster, putty surfaces.
Having finished preparing the planes, the workers measure them: the installers measure the top, those who glue the walls - the side fences.

How is the process going? Installers install baguettes (framework). When the sides dry after finishing, they are pasted over. Cut off excess edges using a sharp clerical knife. This is done before the fabric is stretched so as not to damage it. Having pasted over the fences, they are waiting for them to dry. After the installers pull the base.

When is wallpaper glued first?

Such a choice is made by those who have a modest budget, not wanting to risk damage and pollution when finishing operations. This is rational, since mixtures of building materials are difficult to wash off.

Important! When preparing to mount a wallpaper or a tensile structure, they are guided by the following: first, dirty treatments occur, which subsequently seriously stain the further finish.

What does this method hide? The disadvantages are:

Reference! Statistics say that the wallpaper is changed in the interval of 3-4 years. This causes difficulty in peeling off old tapestries when they are pressed against the baguette. Therefore, they think in advance about the right pasting technology, the frequency of changing the interior.

To begin with, consider the standard implementation, in which the canvas is tightly attached to the profile. If the top sheet is installed, and then the tapestries are glued, the risk of staining the fabric is high, because they are pulled up to a sufficient height. The conclusion is simple: start from the sides, gradually moving to the roof.

When is a stretch ceiling made first?

If the top is first installed, the walls are still prepared for pasting. After all, when a baguette is fixed, and the sides are uneven, it looks sloppy. Damage is visible through the decor. Therefore, the side planes are first leveled and puttied.

Before installing baguettes for stretch ceilings, it is necessary to align the walls in advance

Note! Initially, when installing the top, it is taken into account that the side canvases are more easily protected from harmful effects than the ceiling. But even protecting the upper is an inconvenient, difficult process that does not significantly reduce the risk of damage and contamination of the surface.

What are the other difficulties? The cost of the material, which not everyone can afford. The top is stained with chemical adhesives. Accidentally smeared - the spots are cleaned, which is painstakingly cut - additional chores. When the decor technological tape is pulled, it is evenly cut, excluding distortions with excesses. The process of fitting wallpaper to the canvas requires skills. There is a high probability of touching the tape, tearing the expensive canvas.

The conclusion is simple: professionals will do it well, but their choice increases the requirements of the level of skill, and the owner of the house needs enough money for vinyl covering. What are the benefits? While the top is being treated, a drying gun is used and the side rails retain their coating unless the gun is heated to high temperatures, do not aim at walls. Also, the trellises are easy to replace.

When light colors from paper or fabric are selected for processing the side surfaces, glue them by setting the ceiling. They are weak when wet cleansing. But the profile is attached to the side planes by drilling holes in it. If the house is built of red brick, there will be a lot of dust, without wet cleaning in any way.

Attention! Providing for an interior with painted wallpaper, they are first glued, painted, and then the top is mounted.

Ceiling installation process:

Install profiles.
Stretch and smooth the fabric.
Warm it up with hot air using a cannon.
Fix the heated cloth in the necessary places.

After work, the surface cools down for about 3 hours. At this time, open the windows, ventilate the room.

For beginners in the construction business, for simplicity, the concept of installation is divided into two types: harpoon and without it.

The sequence of the first: they measure the room to the size of the future panel, mount the baguette, which is laid on nails driven into the wall. The design "takes" 4 cm of the height of the plane. Then the cloth is heated, pulled, snapped into place. Sometimes it is made with a notch under the curtain or put on a certain part of the room. Drying, it hardens, but evenly covers the top.

Harpoonless method - the base is clamped like fabric on a hoop. The method is cheaper, simpler, excluding measurements, fabrication. But a greater risk of sagging material.

If you paste the wallpaper first

Let's ask ourselves: if the top is mounted first, and then the sides are pasted over, which will suffer more? The answer is unequivocal - the ceiling, because it is more expensive. The damage done to the trellises is nothing compared to the reverse outcome. V last resort, it’s easier to re-glue one strip of the side fence than to buy a new stretch ceiling canvas. A weighty argument in favor of the original side trim.

The option is convenient if the budget is small, and you decide to save money by making repairs yourself. A huge plus of the initial application of trellises is free, fast work. You calmly, confidently decorate the side rails without fear of getting the top dirty.

Sequence of work:

Glue wallpaper.
Install the frame under the ceilings.
Stretch the fabric of stretch ceilings.

Remember! The ceiling in the glued room is mounted, observing the measures to protect the walls from dirt and damage. The main enemy of damp wallpaper is a draft, sudden climatic changes. The room dries for at least 5 days, then the four sides are covered with a film and work begins.

If you first make stretch ceilings

Why is the top installed first, and then the sides are pasted over? Arguments:

Even when using gas gun, excluding its direction to the side, the wall covering is preserved with careful, careful handling.
Despite the dust generated from drilling under the baguette, vacuuming in time, washing (if washing) the wallpaper, avoid damage to the side fences.
Often, manufacturers themselves urge to first mount the frame on flat planes.
When the suspended structure is first mounted, do not be afraid to paint the fences and trellises. The top is carefully protected with masking tape, and if necessary, a ceiling plinth is used, the gap between the top and side supports of the room is re-glued.

Installation of stretch ceilings before wallpapering

When renovating, homeowners agree on how often they want to change side rail designs. If 1-2 times a year, they are glued in contact with a decorative plinth. Subsequently, they can be easily removed, while the tension structure will not suffer.

The procedure in this case is as follows:

Prepare the side planes.
Install the frame under the stretch ceilings.
Stretch the base.
Mount decorative plinth.
Apply wallpaper.

Remember! The decorative plinth is mounted when the base is stretched. It is fixed to a bare wall.

This is an exceptional example in which the top is set first. But then every year or more you will only change the trellis without worrying about damaging the base.

Have you forgotten about the multi-tiered bases? After all, customers often design the structure in several tiers with intricate plasterboard figures and wonder what they are doing first. First, the base is puttied. After that, unpleasant marks remain on the walls with new patterns. This leads to the conclusion: first they process the top, then they move on to the side rails. The fabric or vinyl is stretched at the end - this is the finishing operation.

Found a good alternative

There is a rare but effective method that guarantees a high-quality result, minimizing the shortcomings of previous methods. It's called - phased installation ceilings. It is used infrequently because it increases downtime and financial costs.

Sequence :

The side surfaces are leveled.
Install a baguette under the ceilings.
Glue the fences on 4 sides.
Mount the cloth.

What disadvantages are avoided in comparison with traditional technologies? We read below:

The frame is placed exactly on the developed wall. There are no gaps or cracks.
The baguette is strengthened in such a way that dust does not harm the trellises.
Wallpaper is easy to glue and paint, eliminating clogging of fabric or vinyl. They are easier to fit to the baguette, small gaps are covered with decorative elements.
When the side surfaces are completely dry, all sides are applied protective film reducing temperature effects. Then, without threats to the tapestries, the canvas is mounted.
When, the room is not warmed up, which is optimal for covering the top and sides. By choosing this method, they accumulate a budget, achieving productive results.

Today it is the most professional option, which has one feature - the effect of temperature. But when the fences dry out for 5-7 days, the risks are insignificant.

What do the experts think?

There is no clear answer even among professionals. They push, advise, but the responsibility for planning design solutions you carry. Some recommend starting from the base, others from the wallpaper. What are the reasons for the first option? The statements are as follows:

The sides, after installing the ceiling structure, sometimes crack from gravity. After the finishing work is done, the work is wasted.
They keep repeating about a lot of dust. And if the house is old, and even made of brick, the appearance of pasted over tones is at risk.
When mounting a profile or panel, the walls are touched, leaving traces of dirty hands and special equipment in different parts of the room.
It is better to play it safe, avoiding the effect of a heat gun on new wallpaper. At temperatures of 60 degrees and above, the adhesive may not withstand. The walls are allowed to dry for 7 days. This minimizes their flaking, blistering.

After completing all the repair procedures, carefully clean the room. The tension surface is cleaned with a vacuum cleaner, a damp cloth. When absorbing dirt with a cloth, use a non-rough brush with the addition of 3-4 drops detergent. For a characteristic shine of the surface, it is wiped with an ammonia solution 1: 9.

A successful choice is the key to a comfortable life

Having considered all the options, they choose based on finances, individual preferences, services construction company. All varieties have both positive and negative sides. If you are going to change the wallpaper more than once every 10 years, or are planning a multi-tiered ceiling structure, then it is better to first make stretch ceilings, and then paste the wallpaper. In other cases, you can safely paste the wallpaper, and then install the ceilings. For maximum effect, they devote time to the issues of room changes, study the details, look for quality craftsmen. We wish you happy design incarnations!

When organizing the process of finishing an apartment, a dilemma inevitably arises: when to install a stretch ceiling - after wallpapering or before? There is no single solution to this problem, which is why it would be more correct to choose one or another solution depending on the circumstances.

The main difficulty in solving this issue is the fact that these works are carried out by different specialists: finishers are invited to stick wallpaper, and installers are engaged in ceiling tension. Each of the teams does not want to take responsibility for the possible damage to the already completed amount of work, so the contractors are trying to persuade the customer to complete their task at the beginning.

Indeed, if you set suspended ceiling after wallpapering the walls, there is a risk of damage to the tapestries during installation, especially when drilling holes for attaching the profile. At this point, a large amount of concrete dust appears, which inevitably falls on the wallpaper.

Clean the textured material from this kind of clogging, without losing original form wallpaper, it will be very difficult. In addition, when the web is tensioned, it is necessary to create elevated temperature indoors, which can also affect the structure of the adhesive and cause the sheets to peel off the walls.

You can also understand the finishers - when fitting, they have to manipulate the wallpaper at the junction of the wall with the suspended ceiling: cut, level, sometimes apply additional liquid glue to dried trellises. It is very difficult to carry out such work close to an expensive canvas and not everyone is ready to take responsibility, since the risk of damage to the material is high, and the cost of installation and a new canvas are quite high.

To get away from the problem of when to stretch the ceiling - before or after the wallpaper, it is recommended to break up the sequence of processes for performing the tasks of both teams. Installers can start fixing the profile, waiting for the walls to be leveled and primed before wallpapering, and work with the film after the finishers have time to glue the walls. But, unfortunately, neither finishers nor installers like to break up the stages of their work.

So it remains only to study the stages of work in detail and establish that before - the wallpaper or the stretch ceiling must be fixed, for which it is necessary to evaluate the sequence of actions in both options.

If first the wallpaper, and then the ceiling

Consider positive points and the risks of the option when it was decided to first start gluing the walls, and then stretch the ceiling canvas.

In this case, several conditions must be met:

Before the start of work on the installation of the ceiling, at least five days must pass from the moment the pasting is completed so that the tapestries are securely glued to the walls. Otherwise, when using a heat gun in the process of stretching the ceiling, the tapestries may come off;
Before starting work on the installation of a profile for tensioning the web, care should be taken to cover the finished walls with plastic wrap, otherwise the dust that occurs when drilling the walls will spoil the appearance of the wallpaper;
If you initially start pasting, the upper part of the wallpaper is under the ceiling profile. On the one hand, this provides an even line of contact, but if it is necessary to update the wall covering, it will not be easy to make a high-quality dismantling of old wallpaper.

If first the ceiling, and then the wallpaper

If the installers insisted on their own, and it was decided to make the ceiling first, and then stick the wallpaper, other problems and positive aspects arise.

Positive aspects of the initial installation of the ceiling:

to start work on pasting the walls does not require a break - you can immediately start work;
rubbish that occurs during the installation of the profile is easily removed from the room;
the thermal effect required to tension the web does not have negative influence on unpaved walls.

Negative points that arise when installing the ceiling in the first place:

during the production of works on pasting walls, cuts of the stretched ceiling cloth are possible;
the need to adjust the tapestries along the upper edge leads to contamination of the ceiling material;
when installing a ceiling molding, which smooths out the flaws in the installation of trellises along the upper edge, damage and contamination of the canvas is also possible.

Which is better first - arguments for and against

Having considered the negative and positive aspects of the sequence, it can be stated that the sequence is not particularly important, since there are ways to minimize all risks and the possibility of organizing safe work.

First, consider options for correcting undesirable situations during the initial installation of wallpaper:

You can protect the surface of the wall covering with a plastic film, which is attached with adhesive tape along the upper border of the wall. After such preparation, drilling for the installation of a ceiling profile can be carried out without loss;
Protecting the surface of the wall pasted over vinyl wallpaper, is also possible when using a film. The film will protect the tapestries from active thermal effects when stretching the ceiling fabric.

For problems that arise when the ceiling is installed before gluing, the following solutions can be envisaged:

You can avoid contamination of the fabric when working with wallpaper glue by pasting the perimeter of the canvas with masking tape. This material does not have a strong adhesive base, and therefore easily detaches from the surface without leaving marks. It is impossible to use traditional adhesive tape for these purposes, since it will not be possible to remove glue residue after it;
To avoid damage to the canvas when cutting the upper edge of the wallpaper, it is enough to remove exact dimensions the height of the wall, after which on the floor mark each sheet according to the measure. As a result, no adjustment is required. If you still need to cut off the excess strip from the trellis at the top, you need to use a wide spatula as a base for making the cut and a sharp clerical knife. In this case, there will be no problems with precise cutting, and the ceiling will remain unharmed.

In order not to argue with the builders about the fact that the first thing is wallpaper or a stretch ceiling, it is better to invite a team that is able to complete the entire range of finishing work. In this case, the master himself will decide what work to perform in the first place in order to prevent damage to the material and violation of the fine finish.

When performing work by one team, the following algorithm of actions is acceptable:

The walls are being prepared for wallpapering, at the same time the ceiling surface is being prepared (remnants of paint or whitewash are removed, cracks are puttied, primer is applied).
A ceiling profile is installed.
Wall papering is in progress.
The canvas is stretched.

This sequence of actions allows you to avoid any problems when pasting and installing the ceiling.

What can influence the choice of the order of work

When making a decision, the following factors should be taken into account:

Sticking trellises involves the installation of a ceiling plinth or not.
What material is the basis for wallpaper installation.
wallpaper type and quality characteristics glue used.
What profile system is used to install the web.
What canvas is planned to be mounted.
Estimated date of the next repair.

Considering all of the above points, you can decide that first - the wallpaper or stretch ceiling needs to be installed, while it is not recommended to rely on the opinion of employees who defend their own interests.

Hello!

My wife and I do repairs with our own hands, and so we argued: what do they do first - a stretch ceiling or wallpaper? Regarding the old wallpaper, we agreed that they need to be removed before the installation of the ceilings, because otherwise their upper part will remain under it.

But this is not the last repair in our lives, someday we will have to renew the walls. And if you stick wallpaper under a stretch ceiling now, then it will be problematic to remove them later. Therefore, I think they are glued last.

And my wife is afraid that during pasting we can inadvertently damage a thin canvas, the price of which is very noticeable for our budget. I beg you to resolve our dispute and tell us how to do it right.

Hello Egor. In general, the instruction says that the walls are first leveled, then the ceilings are installed, and the wallpaper is glued last. But you can decide for yourself, stretch ceiling first or wallpaper, depending on how you feel more comfortable.

Both options have their pros and cons. Let's talk about them in more detail.

Ceilings first

This option is preferred by professional finishers, as it allows them to not have to worry about building debris staining the walls. At self finishing it also has benefits.

pros

When deciding what to do first with wallpaper or stretch ceiling, and choosing the latter, you need to consider the following points:

The material the walls are made of. If it's red ceramic brick, then when drilling walls for fixing baguettes, red dust will fall on them. On light wallpaper, it can leave noticeable traces. But you can avoid their appearance if you keep a vacuum cleaner nozzle under the puncher during drilling.