Do-it-yourself linoleum glue. How to make glue from foam or linoleum - detailed instructions What kind of foam is needed - especially the preparation of glue

Learn how at home you can make affordable quality glue for almost any purpose: from wallpapering to metal (cold welding).

Universal glue

In solvent 647 (can be replaced with toluene, gasoline or acetone), put the foam and mix. Styrofoam is added until the liquid becomes viscous. If you need not very strong glue, for example, for gluing paper, glass, wood, then the glue is ready. For gluing more serious things, we prepare further.

For 100 ml of the resulting liquid, add 2 tbsp. l. any nitro paint. Mix thoroughly.

Add small shavings of wood and metal. For 100 ml of glue - 2 tbsp. l. shavings. We mix. If the glue should not have shrinkage, then increase the amount of chips by 2 times. If you increase the amount of chips by 10 times, you get glue putty.

We add soda. For 100 ml of glue - 2 tbsp. l. soda. We mix. Glue is ready. It can be stored for about a month in a tightly closed container. Glues almost everything. Setting time 30-60 minutes, complete solidification - 24 hours.

General purpose linoleum adhesive

We remove the substrate from the linoleum (if any), cut it into small pieces with scissors and fill it with 647 solvent (toluene, gasoline or acetone) so that it completely covers the linoleum. Tightly close the container with glue with a lid for 24 hours until ready. Apply in a very thin layer, as the adhesive shrinks. Bonds almost any surface. Setting time - 30-90 minutes, complete cooling - 24 hours. If you need glue putty, then add grated chalk, which should be 2 times more than glue.

Glue for rubber

This glue is good for gluing cameras, boats and other rubber products.

It is also made as glue from linoleum. Finely cut rubber, for example, from old cameras, is filled with 647 solvent (toluene, gasoline or acetone) so that it completely covers the rubber. Ideally, it is better to use aviation gasoline. Cover tightly with a lid and wait a few days (depending on the density of the rubber) until the rubber is completely dissolved.

Cold welding

To get cold welding, you need to generously lubricate the place of gluing with superglue. After joining, pour soda on the joint. Wait 10-15 min. and shake off excess soda. If the surface for gluing is not perfectly flat, then first pour soda so that it penetrates all the cracks, and then pour superglue on it.

Epoxy adhesive

Such glue, according to some reviews, is even better than superglue.

We mix epoxy resin with a hardener in proportions of 1:10 at temperatures up to 25 °C. They are sold in hardware stores. Read the exact proportions on the packaging for epoxy resin, since they may differ from different manufacturers. To accurately reproduce the recipe, use a kitchen scale or measuring cup. Use immediately after preparation or packaged in medical syringes, blocking the oxygen with caps.

acrylic adhesive

Relevant if you want to mask the seam. The glue will take on the color of acrylic paint.

PVA glue mixed with acrylic paint in a ratio of 4:1. When gluing, you need to fix the product for 24 hours.

Paste

It can be used for gluing paper, cardboard, wood and other products with a porous surface.

Flour or starch (it is better to use corn starch) is poured with water in a ratio of 1: 3. Mix clockwise with any object or beat with a mixer or blender until smooth without lumps. First, it is better to mix flour and water in equal proportions, and add the remaining water later. Place the mixture over medium heat and bring to a boil, stirring constantly. The finished paste should have the consistency of a thick jelly.

Alternative to PVA glue

This glue is similar in properties to PVA. Can bond wood and paper.

2.5 photographic gelatin (not to be confused with food gelatin) insist 24 hours in 500 ml of water. Add 50 gr. to the infused gelatin. flour and bring to a temperature of 90 ° C. This process is best carried out in a water bath with continuous stirring. The consistency of the glue should resemble a paste. Cool under the lid to room temperature. We add 2 gr. glycerin and 10 ml of alcohol or vodka.

Casein glue from milk or cottage cheese

Such glue is used for gluing porous surfaces, foam, wood, leather, porcelain, ceramics, plastic, fabric. Gives shrinkage.

We heat half a liter of milk to 80 ° C. Add 3 tbsp. l. table vinegar (9%) or 1/5 tsp. citric acid. Mix well. Milk, if it is real, should react and the casein will precipitate.

Instead of milk, you can use cottage cheese. To do this, add 1 tbsp to 0.5 liters of water. l. soda and 0.5 kg of cottage cheese. Mix and infuse for 30 minutes. The further cooking process is the same as for milk casein.

We filter the casein through a sieve or. There should be less moisture in casein, so it is advisable to additionally soak on napkins or rags. Leave for some time (about a day) in a dry place until completely hardened. Grind in a coffee grinder to a powder.

You can skip this step if you buy casein powder from the hardware store. When you need glue, dilute the powder with water in a ratio of 1: 2. Add water in a very thin stream, stirring constantly in a circle. For these purposes, it is better to use a blender or a drill with a mixer attachment. Leave for 40 minutes, then mix again.

This list can be listed indefinitely. After all, even many natural furniture from expensive wood (and not chipboard) in some parts is kept on glue. And the nature of chipboard itself, or MDF, is also adhesive. Glue, despite its external slenderness, can hold almost any material. Not only paper, cardboard, plywood, but even metal, glass, stone! In particular, many adhesives adhere well to porcelain fragments, even rather large ones.

Of course, due to such a variety of functions of the adhesive, it has multiplied accordingly, and there are special adhesives. Some - for thin, "paper" work, others - for working with wood. Everyone has their own recipe, there is casein, there are celluloid adhesives, there are natural and synthetic ones.

And there are universal adhesives. For example, PVA will glue both wood and paper, and that's not all. But who's stopping you from making your own all-purpose glue? Properly prepared at home glue is no worse than purchased, and even better. After all, you follow the process, you are responsible for the quality. But no one is particularly responsible for the quality of the glue bought in the store - take a pig in a poke.

If you want a refurbishment done to the conscience, in which the wallpaper does not roll back into rolls directly from the walls, and the linoleum does not bubble up, then boil the glue yourself.

You can weld glue for any work, but it will be quite a long time. However, if you don’t want to mess around for so long, and you need glue “at once”, without long storage in a jar, you can also prepare faster glue. There are several recipes for acetone-based adhesives. Acetone- a truly magical thing, he will dissolve whatever he wants.

So, the first option. Take a jar, pour a little acetone - half a glass, maybe even less. Now take the unnecessary foam packaging from something. Break it into small pieces and gradually throw these pieces into your bankus with acetone. Acetone dissolves them instantly, and you, as the pieces disappear polystyrene, feed the acetone more and more until the jar is full and there is no acetone at all. You will get just a thick mass. This glue is good for gluing linoleum, another coating.

Option two - again acetone, again linoleum, but in a different capacity. Linoleum will be part of the future glue. To do this, you need to cut it finely (let's say you laid the floor and you have an unnecessary piece left), removing the base. After that, again, take a jar, pour acetone there and start gradually adding linoleum shavings. Acetone will dissolve it, the mass will become thick and sticky. It must be left under the lid for half a day so that it reaches its condition. This glue is more versatile. It bonds metal and wood, ceramics, porcelain and fabric, and even glass.

The third version of acetone glue is made using photographic film. Now few people use this method of photography, perhaps you have old unnecessary photographic films. First, rinse the film thoroughly with a cloth under heated water, removing the emulsion coating from it. Then, again, cut it, and crumble the bankus with acetone. Acetone should be 3 times more than the film itself. That's all. Ready-made glue holds paper and wood well, as well as fabric. This glue is not afraid of getting wet. The water won't loosen his steely grip.

If you need to glue plastic, the most the best way – casein glue th. You can buy this substance, you can cook it yourself. To do this, take low-fat milk and let it sour in the sun. Then filter through a blotter, not gauze. A substance similar to cottage cheese is almost casein. Wash it and tie it in a bundle - and boil it on fire. This removes unwanted fat. What remains is casein, which, when dried, turns into a powder. Take borax and 10 times more casein, mix, add a couple of glasses of water - to make a pasty mass. And then more water. Everything, the glue is ready.

During repairs, at any time you may need a universal tool with which you can connect various parts. But what if there is no way to urgently run to the store? That's right, make glue from linoleum with your own hands.

Required Ingredients

Surely, if you look carefully, most people have small pieces of old (or new, why not) linoleum. They collect dust on balconies or mezzanines, but meanwhile for this floor covering there is a wonderful application. After all, you can make glue from it with your own hands. Moreover, doing this is no more difficult than choosing the right tool in a building supermarket. And the price of such a product will obviously please, since you only need a couple of simple ingredients. Any will do flooring. For example, Tarkett or another manufacturer.

What you need to prepare the glue:

Before starting the process, linoleum must be separated from the fabric base. The fact is that the lining consists of components that do not dissolve in acetone.

How to make glue from linoleum

The step-by-step instruction looks like this:

Remove dust and other dirt from the coating. If cleanliness is not observed, then foreign impurities may form in the future glue. They will only interfere with the work process. If liquid was used for cleaning detergents then the flooring should be wiped with a dry cloth and allowed to dry thoroughly.
Cut it into small pieces. To do this, you can use sharp scissors or a knife. The smaller they are, the faster they will dissolve, and accordingly, it will take less time to get the finished product. It is advisable to cut the linoleum into fragments of 0.5 centimeters or less.
Put the cut pieces in any stele jar. Please note that this container must be tightly closed, clean and dry. In no case do not use plastic - acetone will dissolve not only the flooring, but also the container.
Fill everything with solvent. Exact proportions not here. It is enough just to ensure that the liquid completely covers the linoleum.
Close container. If it seems that it does not close tightly enough, then you can put a PET bag or a piece of film under the lid.
Dissolution will begin almost immediately. But the final result will be achieved within 10-24 hours. The amount of time depends on how finely the coating pieces were cut. But it is better, nevertheless, to withstand the maximum amount of time.
After the jar with the "mixture" is closed, set it aside and shake the contents periodically. "Shaking" can speed up the process and make the mixture more homogeneous.

If you add the same amount of chalk to the finished glue, you get a mastic for tiles. And if you replace the chalk with wood shavings or sawdust, then putty or putty for windows will come out.

Storage

If provide right conditions content, then the shelf life of such glue is not limited. The remains of the finished glue are stored in a dark place, as the rays of the sun can have a bad effect on it. In addition, during the storage period, it is necessary to tightly close the container. Otherwise, the acetone will quickly evaporate and the mass will harden. Also, do not expose the adhesive to high temperatures- this factor contributes to the rapid evaporation of the solvent and changes in its properties. And most importantly: keep the container of glue away from fire. Acetone is a combustible substance.

What is glue good for?

For anything. Therefore, it can become a very versatile assistant. Homemade linoleum glue connects plastic, wood, paper, metal, tiles. And it's not yet full list materials.

How to use homemade glue

You can apply this composition, like any industrial one - apply a thin layer on one of the surfaces, attach it to another object and press it a little. You can use a brush or spatula. Ready. The parts are securely connected.

Finally

Now you have all the information to make your own glue from improvised materials. If you liked the article on how to make glue from linoleum and acetone, share it in in social networks. If you have any questions or suggestions, leave a comment below this post.

Some more useful information can be found in the video below:

When repairing or building, you will definitely need a universal adhesive that is equally suitable for joining plastic, metal, wood and other materials. It is absolutely not necessary to look for such a universal tool in hardware stores, because it can be made independently.

Universal glue is prepared quite simply: you only need a piece of old linoleum (without a base) and acetone. The preparation of the glue will take very little time (within a few days).

A simple technology will allow you to quickly prepare a universal adhesive. This means that it can be used to bond almost any solid material. If you add a fine filler (sawdust) to the resulting mass, you can get an excellent putty for a window or use it as a putty for wood.

Glue preparation

To obtain an effective glue, you will need a piece of old linoleum, from which the lining (base) comes off. The lining does not dissolve in acetone, as it is made of other materials. To obtain an effective adhesive, the material must be clean: all coarse and fine dust is removed from the surface.

Clean linoleum is cut into small pieces. The smaller they are, the faster acetone will dissolve them, and the substance will turn into glue. If there is no need to save time, then you can cut the linoleum into squares of 0.5-1 cm.

To turn the mixture into glue, any glass container with a tight-fitting lid is suitable. Linoleum is poured into the jar, which is poured with acetone. For tightness, a plastic bag is placed under the lid. Shake the jar periodically.

The dissolution of linoleum in acetone begins almost immediately. Regardless of the size of the pieces of material, it dissolves after a few days. Store the resulting product in a cool and dark place in closed containers. The jar in which the glue was prepared can serve as such a container. Universal adhesive suitable for gluing porcelain, metal, wood, paper, rubber, plastic.

This list can be listed indefinitely. After all, even a lot of natural furniture made of expensive wood (and not chipboard) is held on glue in some details. And the nature of chipboard itself, or MDF, is also adhesive. Glue, despite its external slenderness, can hold almost any material. Not only paper, cardboard, plywood, but even metal, glass, stone! In particular, many adhesives adhere well to porcelain fragments, even rather large ones.

Of course, due to such a variety of glue functions, it has multiplied accordingly, and there are special glues. Some - for thin, "paper" work, others - for working with wood. Everyone has their own recipe, there is casein, there are celluloid adhesives, there are natural and synthetic ones.

If you want a refurbishment done to the conscience, in which the wallpaper does not roll back into rolls directly from the walls, and the linoleum does not bubble up, then boil the glue yourself.

So, the first option. Take a jar, pour a little acetone - half a glass, maybe even less. Now take the unnecessary foam packaging from something. Break it into small pieces and gradually throw these pieces into your jar of acetone. Acetone dissolves them instantly, and you, as the pieces disappear polystyrene, feed the acetone more and more until the jar is full and there is no acetone at all. It will just be a thick mass. This glue is good for gluing linoleum, another coating.

Option two - again acetone, again linoleum, but in a different capacity. Linoleum will be part of the future glue. To do this, you need to cut it finely (let's say you laid the floor and you have an unnecessary piece left), removing it from the base. After that, again, take a jar, pour acetone there and start gradually adding linoleum shavings. Acetone will dissolve it, the mass will become thick and sticky. It must be left under the lid for half a day so that it reaches its condition. This glue is more versatile. It bonds metal and wood, ceramics, porcelain and fabric, and even glass.

The third version of acetone glue is made using photographic film. Now few people use this method of photography, perhaps you have old unnecessary photographic films. First, thoroughly rinse the film with a rag under heated water, removing the emulsion coating from it. Then, again, cut it up, and crumble it into a jar of acetone. Acetone should be 3 times more than the film itself. That's all. Ready-made glue holds paper and wood well, as well as fabric. This glue is not afraid of getting wet. The water won't loosen his steely grip.

If you need to glue plastic, the best option is casein glue th. You can buy this substance, you can cook it yourself. To do this, take low-fat milk and let it sour in the sun. Then filter through a blotter, not gauze. A substance similar to cottage cheese is almost casein. Wash it and tie it in a bundle - and boil it on fire. This removes unwanted fat. What remains is casein, which, when dried, turns into a powder. Take borax and 10 times more casein, mix, add a couple of glasses of water - to make a pasty mass. And then more water. Everything, the glue is ready.

Forum / Technologies / How to make glue from linoleum?

Ask your question on our forum without registering
and you will quickly receive an answer and advice from our experts and forum visitors!
Why are we so sure of this? Because we pay them for it!

I remember once I saw a program where they said that you don’t need to throw away scraps from linoleum, that you can make excellent glue out of them. But I don't remember exactly what to do. Who made this glue, tell me? And is it really so good that shoes can be glued to them?

Good evening. Linoleum, in the 90s, was poured with acetone and something like glue was obtained (in fact, this is not glue at all, as is commonly believed, but dissolved, not the most environmentally friendly, liquid pvc). Now this cannot be done from linoleum, the quality of the material will not allow. And why, if specialized liquid PVC is now sold in tubes and it is used mainly for sealing cracks in windows, doors, something like PVC sealant. An excellent thing, it should be noted, but not harmless.

Dear guest, stay!

Many people are already making money just by talking on our forum!
For example, like this. Or like this.
You can start chatting on the forum right now. Just log in via Vkontakte or register, it will take one minute.

But if you are passing by, you can still:

We glue linoleum ourselves, with our own hands. Bonding, butt bonding.

My practical experience of gluing linoleum end-to-end.

Homemade adhesive from linoleum and acetone

The quality of the seam, the problems and methods for solving them that I found. (10+)

We glue linoleum ourselves, with our own hands

Linoleum sometimes has to be glued

I did not manage to find linoleum for a room measuring 4.5 x 4.5 m in order to put it without gluing. Yes, and the delivery of such linoleum would cost a pretty penny. I stopped at two panels: 3 and 1.5 meters wide. Such rolls can be brought by my car.

For gluing, I purchased glue for linoleum - cold welding. They say that linoleum can be glued with almost any universal glue, but we need a glue that sticks well and is transparent after drying. So it's better to use a special one. Such glue dissolves linoleum. After drying, the vinyl from the glue and the dissolved edge of the linoleum form a single whole, a very strong connection.

Problems of gluing linoleum

The floor in the room was, of course, not perfectly flat. So the factory smooth edges of the linoleum still did not match exactly. I had to cut. It definitely failed to cut. Maybe there are seasoned professionals who can do this with one continuous movement of the hand. But I assure you, most people will not succeed in cutting two pieces of linoleum with an accuracy of tenths of a millimeter. I cut quite neatly, but still in some places a very small gap, no more than half a millimeter, formed. When gluing, a sufficient amount of glue did not flow into this gap, since it was covered with masking tape.

The painter's tape has peeled off in some places, and the glue has flowed under it. Excess glue was then removed with a knife.

The linoleum at the joint lay unevenly, a very small, but still noticeable wave. This is due to the curvature of the floor. With this wave, he stuck together. The view was monstrous.

What to do?

Thank God, the seam was carefully cut again, the protruding glue was removed, so I did not spoil the linoleum. Now I have discarded the idea of quickly gluing the entire 4.5 meter seam.

I began to glue sequentially, in pieces of a seam of half a meter. I placed heavy objects around the piece to be glued so that the linoleum stretched.

I glued masking tape along both glued edges at a distance of 1 mm from the edge. By the way, in the packaging of the glue itself, the instructions say exactly that, and not the way I did on the advice from the Internet (I glued one tape, then cut it). I made sure that the adhesive tape adhered well to the linoleum and did not lag behind.

I applied glue with a needle, making sure that the glue filled in minor defects. Excess glue was immediately wiped off with a piece of cardboard. Let it dry for 40 minutes. In small defects, the glue went deep and seized only at the very bottom of the seam, closer to the floor. The second time I placed a little glue in the defects, removed the excess, and let it dry again. I did this for three iterations. Now the seam is smooth and strong. Moved on to the next half-meter section. Spent three days on my seam. I got not great, but acceptable result.

Conclusion: you can glue it normally, but you have to work hard. In any case, if you decide to glue linoleum, be aware that the seam will be clearly visible, it will stand out on the linoleum.

Added on 08/15/2013. I slightly changed my technique for gluing linoleum. In order not to glue in half-meter segments, but to make the whole seam at once, first I put a good sticky tape under the seam. I glue both pieces of linoleum to it. This adhesive tape reverse side linoleum plays two roles. Firstly, it prevents the glue from leaking onto the floor and sticking the linoleum to the base. Secondly, it fixes the sheets one relative to the other for some time. Such fixation is unreliable. After a while, the tape will peel off. But while we are gluing, he will hold, replace the load for us. So, let's take a good sticky tape, stick it on the back side along the joint, make sure that the sheets fit snugly together and lie the way we want. Now glue the method described above.

You need to glue linoleum along the stripes of its pattern. If you can’t get by with one piece, then choose linoleum with stripes and glue along these stripes.

Glued linoleum with a pattern ‘Board’. The place of gluing is shown by an arrow.

Glued glossy linoleum with a non-directional pattern. The place of gluing is visible without explanation.

Glue for linoleum can be prepared by yourself

To do this, you need to dissolve linoleum trimmings in an organic solvent. Acetone or P-4 is usually suitable as a solvent. But for each specific linoleum you need to try. We put pieces of linoleum in a solvent in a jar. We close. Stir occasionally until completely dissolved. If it turned out liquid, then add linoleum, if thick, then a solvent. Choose the density yourself, practicing on small test pieces. Homemade glue will not be transparent. It will turn out to be the same color as the linoleum substrate (since it is the bulk of vinyl) with a touch of the top layer.

Keep in mind that the solvents contained in both homemade and purchased glue are poisonous, dangerous if in contact with the eyes. Be careful.

Proper linoleum. Read about how to choose and buy?

Unfortunately, errors occur periodically in articles, they are corrected, articles are supplemented, developed, new ones are being prepared. Subscribe to the news to stay informed.

If something is not clear, be sure to ask!
Ask a Question. Article discussion.

More articles

Do-it-yourself arc welding. Electric welding. Tutorial. Weld seam….
How to learn welding on your own ....

Slouch. Why am I slouching? What to do. Effective exercise from sg…
How to stop slouching. A simple exercise to do once every two days….

Don't eat sausage. Food, the nutritional value, benefit, usefulness, harm, vr ...
Sausage is not worth eating. The composition of the sausage includes ingredients that are unnecessary for the body, ...

How to cut laminated chipboard, chipboard without chips? How to repair chips...
When making furniture, you have to saw chipboard. Chipboard does not like this very much - ...

Furnace with variable room heating….
Interesting design heating furnace with adjustable room heating….

Homemade ladder.

With my own hands. Prefabricated, collapsible, sk…
How to make a reliable folding ladder yourself ....

Advantages and disadvantages of Titan Wild universal glue. Review….
My experience of using Titan Universal Glue (Titan) Wild in construction, and ...

Insulation to keep warm...
Warming, typical mistakes, how to do it right ...

What to glue linoleum on - choosing glue and working with it

With a zealous owner, everything goes into business, even seemingly unnecessary small trimmings, which are difficult to find application.

An excellent universal glue can be made with your own hands from the remnants of linoleum scraps, but only if it is without a fabric base.

To make the glue, you need to put the scraps in a can of oil paint and pour acetone so that the scraps of linoleum are completely covered.

How to make glue from foam or linoleum - detailed instructions

After 15 hours, the glue is ready for use, it can glue everything up to metal, ceramics and porcelain, and if you add chalk flour to this glue in a ratio of 1: 2, then an excellent putty will come out of it for sealing cracks in the floor and on the walls , and if you add chalk flour to the glue in a 1: 1 ratio, then tiles can be glued to this mixture, and even to a wall covered with oil paint, which, by the way, cannot be done using a conventional mortar, but which the tile is laid, so that , with this glue, everything is possible, it’s just a matter of choosing a good tile, and one of the best is rightfully ceramic tiles, Grasaro porcelain stoneware. The products of this company differ from analogues in higher quality and huge selection color palette, shapes and textures, which allows you to embody any design solution into reality. In addition, the undoubted advantage of Grasaro tiles is increased strength and durability, in addition, only environmentally friendly materials are used in the manufacture of ceramics from this company. And, of course, one cannot ignore the company's pricing policy - prices for ceramic tiles and Grasaro porcelain stoneware are quite democratic and affordable for the average layman.

And one more piece of advice - to seal the seam when laying linoleum, you can lay long pieces of linoleum in the cracks, melt with a soldering iron, and then level and smooth.

Adhesive on foam - application

Foam glue, despite the home-made composition, has powerful strength characteristics. It has a good indicator of adhesion to different surfaces. Here are its main areas of application:

sealing roof cracks, joints of slate and roofing material;
gluing interior items, utensils, household products, furniture;
fixing ceiling cornices, skirting boards;
connection of plates, individual pieces of extruded polystyrene foam.

The service life of the tool is long - you don’t have to worry about detaching the fastened parts. There is only one nuance in using homemade glue. It is suitable for hard materials, and on rubber and other soft raw materials it is better not to use it. The agent will cause unnecessary hardening and may ruin the product.

Instructions for preparing glue

How to make glue at home, how to dissolve the foam to get a quality product? Preparation is simple, but follow step by step instructions must clearly:

Get a solvent. They make an adhesive composition from gasoline and acetone, another solvent (toluene, xylene) is also suitable, but they have strong toxic properties. The easiest way is to dissolve the foam with gasoline.
Prepare Styrofoam. The larger the pieces, the thicker the adhesive mass will be.
Pour the solvent into a small jar. Gradually add the foam, broken into crumbs.

Polystyrene will begin to dissolve in the liquid almost immediately, leaving only a viscous mass. You can keep adding crumbs to make a large amount of glue. It is also allowed to take a viscous mass from the solution and use it for its intended purpose.

It is recommended to glue products without delay. The composition is applied to the surface with a brush, leveled, the parts are pressed tightly against each other. Leave to dry completely (the process lasts 24 hours). Excess glue that has come out must be removed immediately - after drying, stubborn streaks are obtained that are difficult to remove.

There is another method for making glue. The foam should be crushed directly where it is supposed to glue the defects. Next, the solvent is carefully poured onto the pieces. The material melts, becomes like honey and begins to glue. It fills cracks, joints, serves as an excellent sealant. The better the finished product is mixed, the stronger, more reliable the glue line will be.

Features of the adhesive composition

The use of solvents always poses a safety hazard, so it is important to take all precautions. Gasoline, acetone are combustible materials, they ignite easily. Work is carried out away from sources of fire, smoking nearby is strictly prohibited! It is advisable to work outdoors or in a well-ventilated area. Otherwise, there is a risk of inhaling solvent vapors.

You can also use glue as protective film on wood products and other materials. You will have to make the solution more liquid, do not add too much foam to it. It is not worth preparing a large portion of the product, it instantly freezes and loses its properties. The drying rate depends on the thickness of the adhesive layer: for quick gluing, a mass is applied with a thin stroke.

How to replace the foam in the composition, if it is not available? Any plastic product, for example, a tennis ball cut into pieces. The technique for preparing glue is similar.

What foam is needed - features of the preparation of glue

There are several types of polystyrene foam. Non-pressed (granular) in appearance - this is a lot of connected balls that crumble heavily. It is he who is best suited for the preparation of glue. Bespressovy foam quickly dissolves in acetone or gasoline, becoming a sticky mass.

It is not so easy to crumble pressed polystyrene foam. It can also dissolve, but due to the complexity in the preparation of adhesive compositions, it is not used. Extruded polystyrene is strong, homogeneous, with a smooth surface. The material is not suitable for the manufacture of adhesive mass.

You can use foam glue on an ongoing basis - it serves for a long time, is not afraid of frost and heat. With the help of the tool, it is possible to save on repairs if you follow the tips and rules.

Instructions for preparing glue from linoleum

Linoleum is not only a beautiful, practical flooring. There is a recipe for universal glue, it is prepared from the remnants of the old flooring. Do this home remedy quick and easy, no special components required. Do-it-yourself linoleum glue is a reliable, strong composition that is suitable for joining such materials:

ceramics;
metal;
wood;
plastic;
glass;
rubber;
cardboard;
paper;
porcelain.

The components for making glue are linoleum trimmings and acetone. You will also need a glass jar with a volume of 1 liter or more with a tight-fitting lid. There is an important condition: if the flooring is without a substrate, it is used in its original form. If there is an insulating layer, it must be torn off.

Step by step manufacturing technique:

Rinse a piece of floor covering, you can use soap. The material must be completely clean.
Dry the linoleum by wiping with a rag. Cut into small pieces (a few millimeters) sharp knife or scissors.
Take a dry, clean jar. Fold in the cut pieces.
Pour the material with acetone so that it completely covers the trimmings.
Put the closed jar in a dark, not cold place.

Linoleum begins to gradually disperse in the solvent, the whole process lasts about 24 hours. The more often you shake the contents of the jar, the faster the composition will be ready. In a day they can glue any surfaces, details. To do this, apply a little product to the base, distribute it in a thin layer, press the product and fix it.

Using this glue is easy - it dries as the acetone evaporates, in a few seconds. By adding an equal amount of wood shavings, you get a quality wood putty or window putty. The introduction of chalk (1: 1) will make it possible to prepare an excellent mastic for laying tiles. The cost of such glue is very low, and the quality is not inferior to the store, so you can use it everywhere.